非甲烷总经分析仪

规格：双填充柱材质：不锈钢配适机器型号：需客户提供相关信息柱两端中心距离：需客户提供相关信息进样端与检测端高度差：需客户提供相关信息特殊工艺制造，专用于除甲烷以外的烃类的检测分析

产品描述：可用于收集一氧化碳 （CO），二氧化硫（SO2），硫化氢（H2S），苯，氡和硫醇，碳氢化合物及氯化溶剂气体。适合短期储存低浓度（ppm、ppb级）腐蚀性气体和化学活性气体（做预饱和处理 ）。光敏化合物和卤代挥发性有机物（VOC）及非甲烷总烃的收集。Tedlar® PVF采样袋适用于采用美国EPA分析方法，包括溶出实验(TCLP), TO-3(VOCs), TO-12 (NMOC), TO-14A (VOCs), TO-15 (VOCs), ASTM D-5504及其他各种大气气体采集方法。储存温度：0℃~40℃玉衡云测是实验室设备耗材采购一站式服务商，为实验室提供专业的设备耗材集采服务。欢迎咨询：杨生：19925199703（微信同号）

产品描述：可用于收集一氧化碳 （CO），二氧化硫（SO2），硫化氢（H2S），苯，氡和硫醇，碳氢化合物及氯化溶剂气体。适合短期储存低浓度（ppm、ppb级）腐蚀性气体和化学活性气体（做预饱和处理 ）。光敏化合物和卤代挥发性有机物（VOC）及非甲烷总烃的收集。Tedlar® PVF采样袋适用于采用美国EPA分析方法，包括溶出实验(TCLP), TO-3(VOCs), TO-12 (NMOC), TO-14A (VOCs), TO-15 (VOCs), ASTM D-5504及其他各种大气气体采集方法。储存温度：0℃~40℃玉衡云测是实验室设备耗材采购一站式服务商，为实验室提供专业的设备耗材集采服务。欢迎咨询：杨生：19925199703（微信同号）

奥利龙 余氯/总氯/PH分析仪产品参数：余氯总氯测量测量范围：0.01-10ppm重现性: ±3%准确度: ±5%分辨率: 0.01 ppm量间隔：2-10 分钟试试剂指示低于20%，警告试剂缺少水样要求最大压力0.5 bar，pH 4 -10，流速30-40 L/h 流量开关水样压力1 barpH 测量0-10温度测量0-50℃输出8 个 RS485，可选4-20 mA 工作温度1℃ - 45℃电源100-240 V，50-60 Hz尺寸67×33×14 cm（宽× 高× 深）/ 45 kg

Shimadzu 总有机碳分析仪(TOC5000)注射器 体积 描述 注射器货号 替换推杆货号 250µ L 1/4-28 UNF末端 006680 031832 2.5mL 1/4-28 UNF 末端 008680 031854

自动牛奶分析仪配件是一种对牛奶成分分析的一种仪器，能快速对乳制品成分进行检测，它是一款价格较低的自动牛奶检测仪。 自动牛奶分析仪配件应用 用于快速检测生鲜乳的多种成分含量，包括：脂肪、蛋白质、非脂乳固体、乳糖、密度、含水率、冰点、电导率、灰分、样品温度等,无需任何化学试剂和辅助设施，操作极为简单，快速、准确地检测出样品中各种成分的含量 适用于奶站、牧场、企业和畜牧兽医站等部门对乳品的检测范围。自动牛奶分析仪配件参数 脂肪：0.01% -25% 非脂乳固体3% -15% 密度：1015 –1040kg/m3， 蛋白质：2% -7%， 乳糖：0.01% -6% 掺水：0% -70% 牛奶温度：1°C –40°C 冰点：-0.400 –0.700°C 盐分：0.4 –1.5% PH：0-14 电导：3-14mS/cm 总固体：0-25% 自动牛奶分析仪配件特点●带蠕动泵，自动清洗 ●安装、操作、维护、校准方便简单。 ●便携式设计紧凑，可用于车载。 ●只需少量牛奶，便可取得精确结果。 ●低功耗，不使用有害化学物质 ●自带RS232接口，方便与计算机连接。 ●内置打印机，实现数据同步打印。 ●两个样本自我校准 ●检测速度：≥60个样品/小时 孚光精仪是全球领先的进口科学仪器和实验室仪器领导品牌服务商，产品技术和性能保持全球领先,拥有牛奶分析仪,食品分析仪在内的全球最为齐全的实验室和科学仪器品类，世界一流的生产工厂和极为苛刻严谨的质量控制体系，确保每个产品是用户满意的完美产品。我们海外工厂拥有超过3000种仪器的大型现代化仓库，可在下单后12小时内从国外直接空运发货，我们位于天津保税区的进口公司众邦企业（天津)国际贸易公司为客户提供全球零延误的进口通关服务。更多关于自动牛奶分析仪价格等诸多信息，孚光精仪会在第一时间更新并呈现出来，了解更多内容请关注孚光精仪官方网站方便获取！

Shimadzu 岛津总有机碳分析仪(TOC5000)用注射器订货信息：体积描述注射器货号替换推杆货号250μL1/4-28 UNF 末端0066800318322.5mL1/4-28 UNF 末端008680031854

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

GC/MS 分析仪标样试剂盒说明 部件号GC/MS 半挥发性化合物分析仪校验混合物 5190-04733 合1 环境样品分析仪Solvents plus 校验混标 G3440-05012GC/MS 农药分析仪内标样品，菲-d10，浓度1000 μg/mL 的二氯甲烷溶液, 4 x 1 mL 5190-0472农药分析仪测试样品溶液，20 种农药的丙酮溶液，浓度10 μg/mL，5 x 1 mL 5190-0468农药校验标样，100 μg/L，3 x 1 mL 5190-0494GC/MS 毒理学校验混合物 5190-0471残留溶剂修方订法467，2A 类，1 x 1 mL 5190-0492残留溶剂修订方法467，2B类低浓度 5190-0513残留溶剂修订方法467，2B 类，1 x 1 mL 5190-0491残留溶剂修订方法467，2C类，1 x 1 mL 5190-0493残留溶剂修订方法467，第1 类 5190-0490用于生物柴油分析的丁三醇内标#1 5982-0024用于生物柴油分析的甘油三葵酸酯内标#2 5982-0025农药保留时间锁定标准溶液, 三种农药的正己烷溶液，浓度10 μg/mL，3 x 1 mL 5190-1441甘油校准标样试剂盒，5 x 1 mL G3440-85028甘油酯的THF 溶液标样，1 x 2 mL G3440-85018FAME 保留时间标样甲苯溶液，5 x 2 mL G3440-85027十九酸甲酯甲苯溶液标准品5 x 10 mL G3440-85026Solvents-plus 检测混标，3 x 2 mL G3440-85012变压器油气体分析仪校验混标，17 L SCOTTY 气瓶 G3440-85007PAH 分析仪校验标样，5 x 2 mL G3440-85009C6 至C12 正构烷烃混标，3 x 2 mL G3440-85013天然气分析仪校验混标，14 L SCOTTY 气瓶 G3440-85017氘代十七烷酸甲酯的十二烷溶液，3 x 2 mL G3440-85029血醇分析仪乙醇校准试剂盒 G3440-85035血醇分析仪多组分醇类校准试剂盒 G3440-85036

【CHNOS洽诺斯】供应美国赛默飞 Thermo Scientific，Thermo Fisher Scientific 系列元素分析仪与气体稳定同位素比率质谱外联EA , TC/EA , GCC/GCTC，GasBench 仪器耗材配件和标准物质。供应配套产品的美国赛默飞Thermo Fisher元素仪器型号：Flash EA1112 CHNS/O , Flash EA1112 N/ Protein , Flash 2000 HT , Flash 2000 CHNS/O , Flash 4000 N/Protein, NA 2000 , NA 2500；供应配套产品的稳定同位素比率质谱外联设备型号：Delta Plus XP , Delta V Advantage , Delta V Plus ，MAT253.【CHNOS洽诺斯】供应下列Thermo Scientific赛默飞仪器常用产品：样品容器：锡囊，超净锡囊，银囊，超净银囊，锡箔盘，液体锡囊，液体银囊。标准物质：乙酰苯胺，苯甲酸，苯磺酸，磺胺，L-NS，2,4-二硝基苯腙环己酮，阿托品，烟酰胺，咪唑，碳酰二胺，BBOT，硝基苯胺，L-胱胺酸，蒽，菲，硬脂酸，S-卞基异硫脲盐酸盐，润滑剂，蛋氨酸，天(门)冬氨酸，面食（N），土壤（CN），土壤（CNS）。催化剂及助剂：三氧化二铬，四氧化三钴，镀银氧化钴，氧化钨/氧化铝，三氧化钨，氧化镁除氟剂，线状氧化铜，铂催化剂，氧化催化剂，线状还原铜，高纯铜，超纯铜，线状镀银铜，电解铜，氧化钨粉，氧化铜粉，氧化钴粉，锡粉，氧化银粉，五氧化二钒，四氧化三铅，卤素吸收剂，镀镍碳，玻璃碳屑，铂棒催化剂，铬催化剂。吸收剂和填料：高氯酸镁，分子筛，变色硅胶，硫酸铜，碱石棉，碱石灰，石英棉，石英屑，石英砂，银棉，硅藻土。预装反应管：Flash EA1112, Flash EA2000 CHN /CN/N、CHNS/CNS/S、O 单炉反应管，双炉反应管，N/CN 双炉反应管，单炉反应管，土壤沉积物滤膜测定CN反应管。反应器：石英反应管（CHN/CHNS/O），石英反应管（N/CN），石英热解管（O/OH），衬管（11缝），合金钢反应器(N)，合金钢衬管，合金钢反应器（CN），合金钢坩埚，玻璃碳反应管，陶瓷反应管，石墨反应管，石墨杆，石墨坩埚，玻璃水阱，二氧化碳阱，大体积阱。分离柱：CHN、CN、CHNS、S、O、N 不锈钢/聚四氟色谱分离柱配件：MAS200R自动进样器，自动进样器样品盘，自动进样器滑动杆，自动进样器锥，进样器滑块PTFE，PEEK，双向气动阀膜，四路微阀，针型阀，冷却电风扇，加热元件，铂/铂铑热电偶，打印热敏纸，镍片，各种密封圈。工具：装取样品工具盒（装样模板，弯头镊子、平头镊子、尖头镊子，大样品勺、中样品勺、小样品勺）；固体制样放样工具 ( 固体样品瓶， 玛瑙研钵，固体杯模和压样器，样品盒 )；液体取样封样工具（液体样品瓶，微量移液管，液体容器封口器）；装取催化剂工具盒（手钻，长钩，填料棒，漏斗，试剂勺）。 【CHNOS洽诺斯科技】您身边的元素仪耗材厂商，供应性价比高、种类齐全的洽诺斯与进口产品，产品质量和品牌信誉双重保障，一站式采购，24小时内发货。用于Elementar，Thermo，Euro Vector，Costech，SerCon，Perkin Elmer，Exeter，Jena，Shimadzu，Velp, Leco，Horiba，Eltra，Bruker等公司仪器。长期对大专院校、科研院所、检验检疫局、仪器公司、仪器代理商供货，还提供专业的仪器使用维护和样品分析方面的技术咨询。如有任何需求，请随时联系我们。您可以拨打热线电话，或邮件、QQ留言，还可登陆我公司网站浏览详细信息，洽诺斯人将竭诚为您服务。

指纹分析仪系统配件是为法医研究,刑侦等应用设计的最新最强大的指纹分析系统，指纹分析仪系统满足刑侦成像,证据和背景各种照明图片的处理需求。指纹分析仪系统配件特色结合了先进的成像技术，多波长照明与简单易用的软件，是全球唯一具有有两种操作模式能为公安干警，法医人员提供快速和高质量结果的指纹分析系统。潜指纹和处理过指纹包括le 自动化标准指纹分析或为指纹提供的订制化分析程序。可以用于各种法医摄影，潜指纹显现,处理过的指纹分析，痕迹物证,伪造和篡改文件分析痕迹物证Trace Evidence包括体液，纤维，涂料，玻璃碎片和枪击残留物。伪冒和篡改的文件检验能够识别所有手写和打印的文档。无需培训，几分钟内可获得专业结果：使用操作的自动模式，3个简单步骤实现有效成像和加强。1将证据放置在指纹分析仪样品室内2选择分析和证据的类型3按“运行”按钮。自动分析程序将根据预置的法医学领域常见的分析，或自定义分析的特殊要求运行。多个光源和过滤器可以通过几个途径加强证据的图像。高级模式选择最好的全屏图像或在进一步加强。指纹分析仪系统配件双模式软件：指纹分析仪提供快速，高品质成像的两种操作模式：自动模式使用自动模式，任何没有经验的操作者可以执行分析，并根据预先设定的程序获得结果。软件里包含用于普通法医治疗证据的综合分析程序，但自定义分析或细节分析要调整或是根据具体结果设置，然后使用自动模式执行。指纹，包括化学处理后进行的法学领域常见分析文件， 手写和打印追踪证据， 包括血液，纤维，GSR等。高级模式高级模式中，操作者可以选择全手动控制照明，过滤器和后成像增强这些特定的图像增强处理。高级模式允许专业操作者微调增强过程。指纹分析仪系统配件 高级模式特点：高分辨率成像系统，同时提供500万像素14 bit 的单色和1500万像素的彩色成像。高灵敏度，科学级相机和优化的色彩校正透镜，在可见和红外线波长从400-1000nm区间提供高对比度、高分辨率的图像。总控光源和用于强烈聚焦多波长照明的滤光镜和效果增强。可变波长的窄带光源，用于高度彩色背景里的先进的指纹高光谱成像指纹分析仪系统硬件脱机指纹分析仪有高感光度图像捕捉和多波长照明功能。用户可以使用额外的照明，系统安装，PC硬件和相机镜头选项建立一个系统，以满足任何要求。高感光摄像头1500万像素的彩色成像，35mm宽广角镜头（其它镜头可选），集成第二个摄像头指纹分析仪系统 高强度照明犯罪精简版8×4的多波长光源，32个高效率的LED，高达98种颜色的组合4×20W卤素灯提供可见光/ IR照明长通滤镜摄像机滤光镜400nm，455nm，495nm，530nm，550nm，570nm，590nm，610nm，630nm，645nm，665nm，695nm，715nm，780nm，850nm短通滤波器摄像机滤光镜752nm，660nm，610nm和550nm全部附件包括可在犯罪精简版成像仪产品手册上找到额外的照明组件。

英国KAME KM9106-KM9106便携式综合烟气分析仪，面向未来的模块化整体设计独立的测量模块对传感器进行自动校准，测量模块可灵活配置易于升级，咨询热线，15300030867,13718811058，张经理，欢迎您的来电咨询！高效、长寿的传感器及后处理，自动修正交叉干扰红外分析模块可测量浓度高达50%的CO2和10000ppm的HC严密、可靠的保护系统有效保护了传感器和内部部件针对现场操作人员的设计在现场不必移动主机，通过轻便的小型手操器和数据线便可遥控主机完成所有功能满充电一次可连续工作8小时以上而无须外接电源操作员可自行设定采样、打印和数据采集周期，可存储多达2000组测试结果，不仅可供操作人员日后查询也可下载到计算机使用软件Fireworks进行分析和报表英国KAME KM9106-KM9106便携式综合烟气分析仪，技术特性项目分辨率精度范围测量O20.1%-0.1%+0.2%0 ～ 21%CO1ppm+20ppm400ppm+5%2000ppm+10%2000ppm0 ～10000ppmSO21ppm +5ppm100ppm+5%100ppm0 ～5000ppmNO1ppm+5ppm100ppm+5%100ppm0 ～5000ppmNO21ppm+5ppm100ppm+5%100ppm0 ～1000ppm烟气温度0.1℃+1℃0 ～600℃环境温度0.1℃+1℃0 ～50℃压力0.01mbar+0.5%0 ～150mbar计算CO20.1%+0.3%0 ～99.9%NOx1ppm+5ppm100ppm+5%100ppm0 ～6000ppm净温度0.1℃+1℃0 ～600℃效率0.1%+1.0% 读数0 ～99.9%过空系数0.1%+0.2%0 ～2885.0%损失0.1%+0.2%0 ～99.9%CO/CO20.0001+0.010 ～0.9999标准配置主机 450mm x230mm x 300mm手操器 220mm x 55mm x120mm标准探针 350mm x 8mm 烟气导管 5m充电器 操作手册总重量 9.5Kg任选配置红外CO2+HC分析模块 1000mm 探针1200℃ 高温探针烟黑探针Fireworks 分析软件

公司简介： 质谱佳科技是国内专业从事分析仪器维修等技术服务、进口二手分析仪器销售和租赁的领先企业，原厂工程师团队为客户在色谱、光谱、质谱仪的维护保养、维修、仪器认证、技术升级、仪器搬迁，软硬件操作培训等多方面提供完善的技术支持和整体解决方案。 质谱佳科技在美国、欧洲、日本有着良好的合作伙伴，凭借优质的进货渠道和专业的选品团队为客户提供优质的二手仪器。主营品牌有：Thermo（赛默飞）、AB Sciex（爱博才思） 、Agilent (安捷伦)、Waters（沃特世）、Shimadzu（岛津）等，另外质谱佳科技还提供分析仪器配件、耗材的销售。 质谱佳科技总部位于长沙，通过设在上海、海口等地的分公司，形成服务全国的网络。为制药、食品、环保、三方检测、新能源等多个行业以及高校、科研院所、政府实验室等客户提供方便快捷的本地化服务。团队介绍： 公司创始人拥有Agilent、ThermoFisher等国际著名仪器公司工作经历，创办质谱佳科技之前的职位是赛默飞世尔科技（ThermoFisher）湖南售后经理，在色谱、质谱维修上拥有丰富的实战经验。公司拥有多名工程师，均由原厂资深工程师培训授课，全面掌握仪器维修技能。进口分析仪器第三方售后服务市场在国产替代的时代背景下，正加速发展，质谱佳科技也在持续招聘行业内的专业人员加入，扩大我们的团队力量。合作客户： 质谱佳科技自创建以来，凭借精湛或者专业的技术、快捷的服务、经济的价格赢得了众多客户的信赖。我们服务的客户和合作伙伴遍及全国各地，覆盖了第三方检测、制药、食品、环保、化工等行业，以及高校研究院所、政府实验室（药检、海关、质检、食检）。技术团队： 1.技术力量雄厚：公司创始人有世界顶级的分析仪器厂商的工作经验 2.自建零配件仓库：对业务所及的仪器常见的故障准备了配件，以便快速响应客户。 3.“快而灵活”的专业服务：到目前为止所有现场服务需求，我们都能够24小时内响应， 绝大多数48小时内到达现场，真正做到更快速、更周到、更专业。 4.远程支持：我们提供电话、微信、互联网远程在线支持，远程快速诊断及排除故障，大大缩短仪器停机时间，提高客户的工作效率。这些远程免费支持，对偏远地区及对仪器不熟悉的初期客户来说是一个福音。 5.完善的服务体系：我们的工程师训练有素，每一次服务都能做到规范化，可跟踪，符合各行业的法规要求。联系方式：Tel：19376980501产品展示：

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat, set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septumfor syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 piecesmulti N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vesselsfor EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)