余总氯分析仪

奥利龙 余氯/总氯/PH分析仪产品参数：余氯总氯测量测量范围：0.01-10ppm重现性: ±3%准确度: ±5%分辨率: 0.01 ppm量间隔：2-10 分钟试试剂指示低于20%，警告试剂缺少水样要求最大压力0.5 bar，pH 4 -10，流速30-40 L/h 流量开关水样压力1 barpH 测量0-10温度测量0-50℃输出8 个 RS485，可选4-20 mA 工作温度1℃ - 45℃电源100-240 V，50-60 Hz尺寸67×33×14 cm（宽× 高× 深）/ 45 kg

波利梅特龙polymetron 9184sc 余氯分析仪,特点 (销售热线：13718811058，欢迎您的来电）● 量程宽且检出限低 ● 采用选择性膜传感器 ● 带pH和温度补偿 ● 内置流量控制装置 ● 维护量小：校正两月一次；更换电解液和膜六个月一次 ● 即插即用的数字化技术。波利梅特龙polymetron 9184sc 余氯分析仪简介：波利梅特龙polymetron 9184sc 余氯分析仪原理： 电解液和渗透膜把电解池和水样品隔开，渗透膜可以选择性让ClO-穿透；在两个传感器之间有一个固定电位差，生成的电流强度可以换算成余氯浓度： 在阴极上：ClO- + 2H+ + 2e- → Cl- + H2O 在阳极上：Cl- + Ag → AgCl + e- 由于在一定温度和pH值条件下，HOCl、ClO-和余氯之间存在固定的换算关系，通过这种方式可测量余氯。波利梅特龙polymetron 9184sc 余氯分析仪,技术指标：技术指标测量范围：0.005-20mg/L，HOCl最小检出限：0.005mg/L，HOCl准确度：2%或±0.010mg/L，HOCl响应时间：90%小于90秒样品流速：200-250ml/min自动可调存储温度：-20-60℃操作温度：0-45℃样品温度：0-45℃校正方法：实验室比对法校正间隔：两个月一次维护间隔：一般六个月更换一次膜和电解液进样连接：1/4" O.D.排放连接：1/2" I.D.防护等级：IP66/NEMA 4X仪器尺寸：270×250mm波利梅特龙polymetron 9184sc 余氯分析仪,订货号：订购指南：注：pH传感器：368416,00000货号已停产，请选用替代货号：368417,00000TFC余氯分析仪LXV432.99.00001包括9184sc TFC传感器LXV404.99.00502SC200标准控制器，单通道，数字化传感器LXV404.99.01502SC200标准控制器，单通道，数字化传感器,带MODBUS RS232/485LXV404.99.00552SC200标准型控制器，双通道，数字化传感器LXV404.99.01552SC200标准型控制器，双通道，数字化传感器，带MODBUS RS232/48560432-00（停产）包括9184sc TFC传感器(带pH传感器),sc100控制器及安装板60432-01（停产）包括9184sc TFC传感器(带pH传感器),sc100控制器及安装板,带RS485MODBUS60432-02（停产）包括9184sc TFC传感器(带pH传感器),sc100控制器及安装板,带RS232MODBUSHOCl（次氯酸）分析仪LXV430.99.00001包括9184sc HOCl传感器LXV404.99.00502SC200标准控制器，单通道，数字化传感器LXV404.99.01502SC200标准控制器，单通道，数字化传感器,带MODBUS RS232/485LXV404.99.00552SC200标准型控制器，双通道，数字化传感器LXV404.99.01552SC200标准型控制器，双通道，数字化传感器，带MODBUS RS232/48560430-00（停产）包括9184sc HOCl传感器(带pH传感器)，sc100控制器及安装板60430-01（停产）包括9184sc HOCl传感器(带pH传感器)，sc100控制器及安装板,带RS485MODBUS60430-02（停产）包括9184sc HOCl传感器(带pH传感器)，sc100控制器及安装板,带RS232MODBUS传感器和消耗品LXV430.99.00001包括9184sc HOCl传感器LXV432.99.00001包括9184sc TFC传感器368416,00000pH传感器（368416,00000货号已停产，请选用替代型号：368417,00000）368417,00000pH传感器09184=A=10019184sc传感器09184=A=35009184sc膜，已经组装，4只09184=A=36009184sc电解液波利梅特龙polymetron 9184sc 余氯分析仪,波利梅特龙polymetron 9184sc 余氯分析仪

MI413余氯/总氯测定仪 Milwaukee提供了应用在所有范围的氯比色计：测量游泳池处理，家庭洗衣店，刷碗机添加剂，洗衣粉/液和冷水处理的氧化消毒剂中的氯。Milwaukee提供了3种微电脑控制，高分辨率，高精准性的比色计，您可以在这三种型号中任意选择。 氯化物是海水中主要的成分，在酸性条件下具有很高的腐蚀性。在船用锅炉系统中要一直监视氯的含量来确保不被海水污染。 型号 Mi413余氯/总氯比色计 MI-80251-07 测量范围 余氯 0.00-10.00MG/L CL2 总氯0.00-10.00MG/L CL2 解析度 余氯0.01mg/L(0.00to3.50mg/L) 0.10mg/L(超过3.50mg/L) 总氯0.01mg/L(0.00to3.50mg/L) 0.10mg/L(超过3.50mg/L) 精度 余氯± 0.10mg/L@5.00mg/L 总氯± 0.10mg/L@5.00mg/L 检测方法 4500-CI G标准法及330.5USEPA法 光源 钨灯 光检测器 硅光电池525NM窄光干涉滤光器 环境温湿度 0to50℃/32to122℉；max RH100% 电池类型 1× 9V 自动关机 10分钟后自动关机 尺寸/重量 192× 104× 52mm/380g

Shimadzu 总有机碳分析仪(TOC5000)注射器 体积 描述 注射器货号 替换推杆货号 250µ L 1/4-28 UNF末端 006680 031832 2.5mL 1/4-28 UNF 末端 008680 031854

哈希 水质测试试纸哈希五合一PH水硬度测试余氯总氯总硬度总碱度测试检测试纸- 产品概述：哈希公司提供的水质测试试纸是一类非常简单、经济的水质测试产品，可对多个参数作半定量分析。- 应用行业：适用于各个环境的现场工艺排查。盐湖、废水，水产养殖等现场水质检测。同时也适用于家庭自来水、饮用水、旅游用水、动物用水、幼儿科普等。- 产品特点：适用于各个环境的现场工艺排查，可快速预判量程范围及稀释倍数。操作简单，方便携带。原装进口，单次检测成本低于3元钱。无需预制试剂，可减少操作人员与基础危险品的接触机会。安全性高。可测量生活用水的水质硬度、余氯总氯和酸碱度，快速筛查符合机体生理需要的水。订购信息2755250 五合一测试试纸 2745250 总硬度测试试纸 2745650 pH测试试纸 2755325 氨氮测试试纸 2744940 氯化物测试试纸 2745050 余氯总氯及游离氯测试试纸 2751340 氯化物测试试纸 2793944 余氯总氯及游离氯测试试纸 2745125 铜测试试纸 2744850 总碱度测试试纸 2745425 硝酸盐、亚硝酸盐测试试纸 2757150 磷酸盐测试试纸 技术指标参数 量程 (mg/L) 测量精度 (mg/L) 测试次数 试纸订货号 五合一测试试纸 总氯 0-10 0, 0.5, 1.0, 2.0, 4.0, 10.0 50 27552-50 余氯 0-10 0, 0.5, 1.0, 2.0, 4.0, 10.0 总硬度 0-25 0, 1.5, 3, 7, 15, 25 0-425 0, 25, 50, 120, 250, 425 总碱度 0-240 0, 40, 80, 120, 180, 240 pH 6.2-8.4 6.2, 6.8, 7.2, 7.8, 8.4 氨氮 0-6 0, 0.25, 0.5, 1.0, 3.0, 6.0 25 27553-25 磷酸盐 0-5 0, 5, 15, 30, 50 50 27571-50 总碱度 0-240 0, 40, 80, 120, 180, 240 50 27448-50 氯化物 30-600 色阶不固定，10-20 递增 40 27449-40 300-6000 色阶不固定，100-200 递增 27513-40 余氯 0-10 0, 0.5, 1.0, 2.0, 4.0, 10.0 50 27450-50 总氯及游离氯 250 27939-44 铜 0-3 0, 0.2, 0.5, 1, 3 25 27451-25 总硬度 0-425 0, 25, 50, 120, 250, 425 50 27452-50 总溶解性铁 0-5 0, 0.15, 0.3, 0.6, 1, 2, 5 25 27453-25 硝酸盐、亚硝酸盐 0-50 0, 1, 2, 5, 10, 20, 50 25 27454-25 0-3 0, 0.15, 0.3, 1, 1.5, 3 25 pH 4-9 4, 5, 6, 7, 8, 9 50 27456-50 0-14 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 100 26013-00 砷 0-500ppb 0, 10, 25, 50, 100, 250, 500ppb 100 28000-00 0-500ppb 0, 10, 25, 50, 100, 250, 500ppb 50 2822800-CN 0-4000ppb 0, 35, 75, 175, 1500, 4000ppb 50

指纹分析仪系统配件是为法医研究,刑侦等应用设计的最新最强大的指纹分析系统，指纹分析仪系统满足刑侦成像,证据和背景各种照明图片的处理需求。指纹分析仪系统配件特色结合了先进的成像技术，多波长照明与简单易用的软件，是全球唯一具有有两种操作模式能为公安干警，法医人员提供快速和高质量结果的指纹分析系统。潜指纹和处理过指纹包括le 自动化标准指纹分析或为指纹提供的订制化分析程序。可以用于各种法医摄影，潜指纹显现,处理过的指纹分析，痕迹物证,伪造和篡改文件分析痕迹物证Trace Evidence包括体液，纤维，涂料，玻璃碎片和枪击残留物。伪冒和篡改的文件检验能够识别所有手写和打印的文档。无需培训，几分钟内可获得专业结果：使用操作的自动模式，3个简单步骤实现有效成像和加强。1将证据放置在指纹分析仪样品室内2选择分析和证据的类型3按“运行”按钮。自动分析程序将根据预置的法医学领域常见的分析，或自定义分析的特殊要求运行。多个光源和过滤器可以通过几个途径加强证据的图像。高级模式选择最好的全屏图像或在进一步加强。指纹分析仪系统配件双模式软件：指纹分析仪提供快速，高品质成像的两种操作模式：自动模式使用自动模式，任何没有经验的操作者可以执行分析，并根据预先设定的程序获得结果。软件里包含用于普通法医治疗证据的综合分析程序，但自定义分析或细节分析要调整或是根据具体结果设置，然后使用自动模式执行。指纹，包括化学处理后进行的法学领域常见分析文件， 手写和打印追踪证据， 包括血液，纤维，GSR等。高级模式高级模式中，操作者可以选择全手动控制照明，过滤器和后成像增强这些特定的图像增强处理。高级模式允许专业操作者微调增强过程。指纹分析仪系统配件 高级模式特点：高分辨率成像系统，同时提供500万像素14 bit 的单色和1500万像素的彩色成像。高灵敏度，科学级相机和优化的色彩校正透镜，在可见和红外线波长从400-1000nm区间提供高对比度、高分辨率的图像。总控光源和用于强烈聚焦多波长照明的滤光镜和效果增强。可变波长的窄带光源，用于高度彩色背景里的先进的指纹高光谱成像指纹分析仪系统硬件脱机指纹分析仪有高感光度图像捕捉和多波长照明功能。用户可以使用额外的照明，系统安装，PC硬件和相机镜头选项建立一个系统，以满足任何要求。高感光摄像头1500万像素的彩色成像，35mm宽广角镜头（其它镜头可选），集成第二个摄像头指纹分析仪系统 高强度照明犯罪精简版8×4的多波长光源，32个高效率的LED，高达98种颜色的组合4×20W卤素灯提供可见光/ IR照明长通滤镜摄像机滤光镜400nm，455nm，495nm，530nm，550nm，570nm，590nm，610nm，630nm，645nm，665nm，695nm，715nm，780nm，850nm短通滤波器摄像机滤光镜752nm，660nm，610nm和550nm全部附件包括可在犯罪精简版成像仪产品手册上找到额外的照明组件。

唐海红 13120400643 特点： *人性化显示界面，操作简单 * 双行易读LCD显示屏 *优良防水性能，同时适用于实验室和现场使用 *具有用户校准功能 *选购专用校正组可进行精确校准 * EPA标准，GLP管理功能 *自动关机节电模式 操作原理： 我们所观察的每个物质所呈现的颜色都是由它的分子把电磁辐射（光）经过一系列的吸收和发射才呈现出来的。比色计的分析原理是一定浓度的混合物之间发生反应，形成颜色，其颜色的深浅与所测量物质的浓度成一定比例。当一种物质被一束强度I。的光照射时，一部分辐射被物质的分子吸收，而一部分强度为I，低于I。的辐射则被发射。 所吸收的辐射量根据Lambert-beer定率可得出：LogI。/I = A　其中：A =&epsilon &lambda cd 在波长为照射&lambda 下，物质分子的摩尔吸收系数 （molar extinction coefficient） c = 物质的摩尔浓度　　d = 光程 由于其它数值是已知的，因此可根据被发射的辐射I所决定的物质的颜色强度，从而算出物质的浓度。 技术参数： 测量范围 余氯 0.00-5.00mg/L 总氯 0.00-5.00mg/L 分辨率 0.01 mg/L（0.00-0.10mg/L） 0.10 mg/L （0.10-3.50 mg/L） 精度 ± 0.02 mg/L@1.00mg/L 波长 钨灯光源@525 nm 测量方法 参照USEPA 330.5和Standard Method 4500-Cl G标准方法，氯样品与DPD试剂反应呈淡粉红色 选购试剂 HI93701-01（余氯试剂 100次）HI93701-03（余氯试剂 300次） 电源 1× 9V电池 数据接口 RS232串口 数据存储 99组数据 自动关机 在测量模式下，10分钟不用后自动关机 尺寸/重量 216× 83× 65 mm/420 g HI96771C 双量程余氯微电脑测量仪 参数名称 参数值 型号 HI 96771 量程 高量程：0 to 500 mg/L Cl2 低量程：0.00 to 5.00 mg/L Cl2 解析度 1mg/L；0.01mg/L 精度 ± 2 mg/L @ 100 mg/L ； ± 0.02 mg/L @ 1.00 mg/L 光学系统 钨灯光源，窄波段滤波器@ 525 nm，硅光电池检光器 校准功能 CAL CHECK单点自动校准功能 供电方式 1 x 9V电池；待机10分钟后自动关机节电功能 使用环境 0 to 50° C(32 to 122° F)；RH max 95%无冷凝 尺寸重量 192 x 102 x 67 mm；290 g 测量方法 参照Standard Methods, 20th edition, 4500-Cl标准方法。氯和试剂反应呈淡黄色(UHR)，淡粉红色(LR)。

自动牛奶分析仪配件是一种对牛奶成分分析的一种仪器，能快速对乳制品成分进行检测，它是一款价格较低的自动牛奶检测仪。 自动牛奶分析仪配件应用 用于快速检测生鲜乳的多种成分含量，包括：脂肪、蛋白质、非脂乳固体、乳糖、密度、含水率、冰点、电导率、灰分、样品温度等,无需任何化学试剂和辅助设施，操作极为简单，快速、准确地检测出样品中各种成分的含量 适用于奶站、牧场、企业和畜牧兽医站等部门对乳品的检测范围。自动牛奶分析仪配件参数 脂肪：0.01% -25% 非脂乳固体3% -15% 密度：1015 –1040kg/m3， 蛋白质：2% -7%， 乳糖：0.01% -6% 掺水：0% -70% 牛奶温度：1°C –40°C 冰点：-0.400 –0.700°C 盐分：0.4 –1.5% PH：0-14 电导：3-14mS/cm 总固体：0-25% 自动牛奶分析仪配件特点●带蠕动泵，自动清洗 ●安装、操作、维护、校准方便简单。 ●便携式设计紧凑，可用于车载。 ●只需少量牛奶，便可取得精确结果。 ●低功耗，不使用有害化学物质 ●自带RS232接口，方便与计算机连接。 ●内置打印机，实现数据同步打印。 ●两个样本自我校准 ●检测速度：≥60个样品/小时 孚光精仪是全球领先的进口科学仪器和实验室仪器领导品牌服务商，产品技术和性能保持全球领先,拥有牛奶分析仪,食品分析仪在内的全球最为齐全的实验室和科学仪器品类，世界一流的生产工厂和极为苛刻严谨的质量控制体系，确保每个产品是用户满意的完美产品。我们海外工厂拥有超过3000种仪器的大型现代化仓库，可在下单后12小时内从国外直接空运发货，我们位于天津保税区的进口公司众邦企业（天津)国际贸易公司为客户提供全球零延误的进口通关服务。更多关于自动牛奶分析仪价格等诸多信息，孚光精仪会在第一时间更新并呈现出来，了解更多内容请关注孚光精仪官方网站方便获取！

纳米颗粒分析仪配件用于观测和分析液体中的微小颗粒的布朗运动速率与尺寸分布相关，采用纳米颗粒跟踪分析（NTA）技术，通过激光散射装置（纳米观测）与超显微镜ultra-microscope和NTA软件的相结合，生成纳米颗粒图像，是全球领先的纳米粒度分析仪。纳米颗粒分析仪配件 纳米观测原理 纳米颗粒分析仪使用纳米透视Nano-Insight 激光散射模块，可以通过顶眼超显微镜观测到液体中的纳米粒子。采用不同激光散射颗粒在矩阵中表现为模糊点。模糊点根据其各自的布朗运动而移动。液体中有不同的布朗运动粒子。小粒子比大粒子受到相邻粒子的影响更少。因此，在超显微图像中，较大的粒子有大的模糊外观。 NTA能够追踪粒子的相应路径。 纳米观测模块 纳米观测模块的设计，可以使其安装在超显微镜，顶眼纳米的底板。可以通过Mishell软件来控制该模块。Mishell软件控制着纳米观测模块以及照相机。根据应用决定在纳米观测模块装备一个或多个激光器。激光器以一种特殊的方式排列。左侧图片上展示的是纳米观测图。较小的粒子比较大的粒子移动更快。我们用摄像机同时跟踪每个粒子。 顶眼超显微镜 顶眼超显微镜将进入模糊点的散射光可视化。用适当的时间分辨跟踪，模糊云可被分配并与各自的粒径相关。粒子的布朗运动图像是唯一的。下面将给出例子。每个模糊点代表单个粒子。 NTA 软件 上图展示的是NTA分析的典型图像。散射激光被捕获到模糊点，要根据时间函数跟踪模糊点。我们跟踪每个模糊点。跟踪每个粒子的方法，得到的技术结果是高分辨率。我们正在寻找与图像相关的量，当我们知道相关的量后，我们就可以极其精确地确定各种粒子的浓度。该技术将会带起许多可能的应用。例如，可能也可以使用荧光激光器。使用荧光激光器，可以瞄准复杂的基质里的一个粒子。该技术带来的好处是，用户可以在视觉上检查并且通过观察相应图像验证所有可能的应用。 MiNan是Mishell® 内的一个模块- 扩展图像分析软件包，被认为是市场上最先进的图像分析软件。MiNan是一个子程序，可以进行Morphious纳米粒子分析的全部描述。 MiNan是自带Morphious纳米系统的软件，研发用于纳米粒子的可视化以及纳米粒子的大小、形状（形态）和浓度的测量。每个粒子是一个个体，但通过观测扩散同时被分析。这种一个粒子后接一个粒子的方法产生高分辨率的结果，即粒子的尺寸分布和浓度分辨率高，同时视觉验证让用户对数据有了额外的信心。当荧光模式检测标记粒子时，粒子尺寸和浓度，蛋白质聚集和粘度都可以被分析。 纳米颗粒分析仪配件应用 ? 在制药或复合产业研发药物 ? 用于病毒筛查 ? 用于开发纳米生物标记物或毒物筛查 ? 用于蛋白质聚集的动力学模型研究 ? 用于通过膜泡的表征研究疾病 ? 用于促进纳米复合材料的发展 纳米颗粒分析仪配件特色 ? 在同一时间多粒子高通量表征 ? 实时视觉展示粒子，允许用户评估试验，无需额外复杂性 ? 方便和易于使用的软件，允许用户通过宏设置任何实验 ? 添加像高通量自动采样器，泵或加热和制冷配件 ? 自适应模块化系统构建任何复杂的应用程序，操作轻松舒适 ? 超级高效和购买成本低 ? 该系统提供高分辨率的粒度特性来研究复杂的多分散矩阵 ? 激光波长可选择 ? 通过给过滤器添加电动轮，得到自适应荧光分析 纳米颗粒分析仪配件参数 ? 尺寸 10 nm - 2000 nm* ? 浓度 106 - 109 粒子/ mL ? 荧光检测 纳米颗粒分析仪配件规格 温度范围 15-40 °C 电源 230V AC/115V AC, 50/60 Hz 摄像机 USB3 CMOS分辨率：1936x1216 161帧/秒，像素尺寸5.86μm：颜色校准模块 功耗 18W 激光波长 405nm（紫色），488nm（蓝），532nm（绿），642nm（红色） 尺寸范围 从10 nm到2000 nm (取决于材料) 焦点 电脑控制电动调焦 个人计算机 SDD亿康 II SDSSDHII-120G-G25HDD 西数蓝WD10EZEX1 TB|主板千兆字节 GA-Z97X-UD3H|内存金士顿骇客神条怒黑| HX318C10FBK2/1616 GB DDR3-RAM 处理器 英特尔® 酷睿™ i7 i7-4790K四核4×4.0 GHz 显卡 PNY VCQK2200-PB 4GB 电源 酷冷至尊 G750M 750w 机箱 酷冷至尊黑 软件 Windows® ＆（或更高）.由Mishell® 供电 Mishell是Microptik BV公司的注册商标。 Windows是微软公司的注册商标。 MiNan尖端程序在Mishell下运行，以充分体现由Morphious纳米获得的纳米粒子 尺寸（长×宽×高） 20 x 18 x 30 cm 重量 10.5 kg

元素分析仪配件 德国耶拿 Jena 402-881.229预过滤器TC prefilter (aerosol trap)

Shimadzu 岛津总有机碳分析仪(TOC5000)用注射器订货信息：体积描述注射器货号替换推杆货号250μL1/4-28 UNF 末端0066800318322.5mL1/4-28 UNF 末端008680031854

元素分析仪配件 德国耶拿 Jena 402-881.245预过滤器和水阱Set TC pre-filter and water trap

操作步骤：一、按待测水样中总余氯含量范围选用高低不同浓度的余氯测试管。二、取100ml水样加入固体KI试剂0.50g,使之溶解并搅拌均匀后,将测试管的毛细管部位完全浸入待测水样中，折断毛细管，待测水样即被自动吸入管中。三、取出测试管，将其来回倒置几次使管中液体混合均匀。四、1-2分钟后，将发生显色反应的测试管插入ZZW水质多参数现场测试仪的插孔中，按测试仪操作程序进行测试。注意事项：一、当待测水样中总余氯含量大于1.0mg/L时，选用高余氯测试管，用测试仪菜单中高余氯进行测试，当待测水样中总余氯含量小于1.0mg/L时，选用低余氯测试管，用测试仪菜单中低余氯进行测试。二、本法测定的为次氯酸盐、氯气等消毒剂处理过的水中总余氯含量；低余氯测试管也可用于二氧化氯消毒剂处理过的水中总余氯含量的测定。三、测定范围： 检出限低余氯 0.15-1.5 mg/L 0.05mg/L 高余氯 1.0-14 mg/L 0.2mg/L四、测试管置于阴凉干燥处储存，有效期一年.

产品分类：余氯：DPD1试剂片总余氯：DPD1+DPD3试剂片二氧化氯：DPD1试剂片+甘氨酸液体试剂仪器校准盒光度计比色管

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

英国KAME KM9106-KM9106便携式综合烟气分析仪，面向未来的模块化整体设计独立的测量模块对传感器进行自动校准，测量模块可灵活配置易于升级，咨询热线，15300030867,13718811058，张经理，欢迎您的来电咨询！高效、长寿的传感器及后处理，自动修正交叉干扰红外分析模块可测量浓度高达50%的CO2和10000ppm的HC严密、可靠的保护系统有效保护了传感器和内部部件针对现场操作人员的设计在现场不必移动主机，通过轻便的小型手操器和数据线便可遥控主机完成所有功能满充电一次可连续工作8小时以上而无须外接电源操作员可自行设定采样、打印和数据采集周期，可存储多达2000组测试结果，不仅可供操作人员日后查询也可下载到计算机使用软件Fireworks进行分析和报表英国KAME KM9106-KM9106便携式综合烟气分析仪，技术特性项目分辨率精度范围测量O20.1%-0.1%+0.2%0 ～ 21%CO1ppm+20ppm400ppm+5%2000ppm+10%2000ppm0 ～10000ppmSO21ppm +5ppm100ppm+5%100ppm0 ～5000ppmNO1ppm+5ppm100ppm+5%100ppm0 ～5000ppmNO21ppm+5ppm100ppm+5%100ppm0 ～1000ppm烟气温度0.1℃+1℃0 ～600℃环境温度0.1℃+1℃0 ～50℃压力0.01mbar+0.5%0 ～150mbar计算CO20.1%+0.3%0 ～99.9%NOx1ppm+5ppm100ppm+5%100ppm0 ～6000ppm净温度0.1℃+1℃0 ～600℃效率0.1%+1.0% 读数0 ～99.9%过空系数0.1%+0.2%0 ～2885.0%损失0.1%+0.2%0 ～99.9%CO/CO20.0001+0.010 ～0.9999标准配置主机 450mm x230mm x 300mm手操器 220mm x 55mm x120mm标准探针 350mm x 8mm 烟气导管 5m充电器 操作手册总重量 9.5Kg任选配置红外CO2+HC分析模块 1000mm 探针1200℃ 高温探针烟黑探针Fireworks 分析软件

407-401.590 德国耶拿Dosing tube MPE (MFA)德国耶拿分析仪器股份公司（Analytik Jena AG，简称AJ公司）成立于1990年，前身为久负盛名的卡尔蔡司公司分析仪器部，传承了蔡司公司160多年的精密光学仪器研发制造经验，拥有德国最大的应用实验室，在德国Jena，Eisfeld，Langeweisen，Berlin和Uberlingen等多个城市设有研发和制造工厂，已发展成为德国最大的分析仪器公司之一，并成为法兰克福证交所上市公司。公司总部设在世界光学精密仪器制造中心的德国耶拿市，在全球90多个国家设有分支机构，其产品在全球拥有20万个以上的用户。德国耶拿中国代表处成立于2001年，回首十几年，耶拿公司在中国一直保持着高速发展的态势，已逐步建立了高品质的专业品牌形象，形成了耶拿中国专业严谨、勤奋敬业的团队文化。“品质造就非凡”是耶拿公司的宗旨，耶拿中国在高速发展的道路上将一如既往地为广大用户提供高品质的产品和服务。 北京龙天韬略科技有限公司代理德国耶拿Analytik Jena原装进口仪器消耗品、配件、辅助材料等相关配件耗材，现货供应常规常用耗材配件 期货产品订货快，到货快 原装正品，品质保证，技术支持。德国耶拿全系列TOC分析仪/总有机碳分析仪 multi N/C® 3100新一代 总有机碳/总氮分析仪multi N/C ® 2100新一代专家型总有机碳/总氮分析仪multi N/C ® UV HS新一代湿法总有机碳/总氮分析仪multi N/C ® Pharma HT新一代制药专用干法总有机碳/总氮分析仪multi N/C ® Pharma UV新一代制药专用湿法总有机碳/总氮分析仪multi EA® 5000碳、氮、硫、氯 元素分析仪multi EA® S 5000碳、氮、硫、氯 元素分析仪multi EA® 4000碳、硫、氯 元素分析仪multi X® 2500总有机卤素分析仪配套使用注射器/进样针/进样器/进样针适用于德国耶拿EA3100和EA5000硫氮氯分析仪器现货供应 价格优惠 货号如下：1、产品货号402-886.311 产品描述Syringe graduated 500 μl with removable needle for manual injection2、产品货号402-889.589 产品描述Syringe 10 μl, for Autoinjector, with removable needle3、产品货号402-889.590 产品描述Syringe 20 μl, for Autoinjector, with removable needle4、产品货号402-889.591 产品描述Syringe 40 μl, for Autoinjector, with removable needle5、产品货号402-889.592 产品描述Syringe 100 μl, for Autoinjector, with removable needle6、产品货号402-823.080 产品描述100μl syringe H ?8 RN 0,64(G23s)c517、产品货号402-886.305 产品描述500μl SYR H ?8Vent 1/4"-28 RN 1,0x0,7c518、产品货号402-823.056 产品描述Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 pieces9、产品货号402-823.106 产品描述Syringe 20 μl, for Autoinjector, with removable needle10、产品货号402-886.306 产品描述Needle 1 mm x 0.7 mm for all types of syringes, 3 pieces11、产品货号402-889.186产品描述 Removable special needles, set of 3 pieces12、产品货号 402-823.079 产品描述 Removable needles for 50 and 100 μl syringes, set of 3 pieces耶拿取样杯1.5ml407-218.852(1000只/包）耶拿原子吸收样品杯

YSI 5000系列实验室BOD分析仪 北京宏昌信科技有限公司销售部 唐海红 13120400643 15321361385 010-59481385 先进的实验室BOD分析仪 YSI 5000系列实验室溶解氧分析仪，配合先进的自搅拌的BOD分析探头和YSI独家拥有的BOD分析软件，实现实验室BOD分析自动化、准确化和标准化。 YSI 5120型 BOD分析软件 · 安装在计算机上，直接驱动溶氧仪，使整个BOD测试过程自动化 · 系统自动存储首、尾天的读数，计算并打印报告 · 当溶解氧读数达到稳定时自动读取并存储读数 · 超饱和样品和温度超越范围警示 · 其它卓越功能包括：自动空白、种样及加荷补偿、非五天测试BOD结果导算，其它稀释度首天读数衍生等 技术参数： 溶解氧（毫克/升）：测量范围 0至60；分辨率 0.01；准确度 ± 0.1%+1lsd 溶解氧（%空气饱和度）：测量范围 0至600%；分辨率 0.1%；准确度 ± 0.1% +1lsd 温度：测量范围 -5至+50℃；分辨率 0.1℃；准确度 ± 0.1℃ 主要特点： · 传统的BOD 稀释测试法，5000系列仪器配合YSI的溶解氧/BOD探头，仪器整体符合国标HJ/T99-2003标准，溶解氧测量符合国标电化学探头法GB11913-89标准，BOD测量完全符合国标GB7488-87标准 · 极其先进的实验室溶氧仪＋自搅拌BOD探头方法（BOD分析软件） · 自动搅拌BOD 电极，单手即可操作 · 可选配BOD分析软件，实现BOD测试自动化，实现数据自动存储BOD自动计算，并打印报告；超饱和样品和温度超越范围警示 · 可实现快速大批量测试 · 搅拌力强，确保测试数据准确 · 搅拌速率恒定，再现性佳 · 内置搅拌器，无需另加搅拌工具，省时，方便 · 使用5906型盖膜：预置已预张的渗透膜，免除安装不当的人为误差 · 无零漂，免调零 · 膜完整性监测，当膜破损时仪器自动警示 · 可存储100组带日期、时间标签的读数 北京宏昌信科技有限公司销售部 唐海红 13120400643 15321361385 010-59481385 YSI 6820V2 / 6920V2型 多参数水质监测仪 YSI 6600V2型 多参数水质监测仪 YSI 600OMS V2 光学监测仪 ，YSI 600OMS V2 光学监测仪 外形小巧、轻便耐固、耗电低，一个光学端口，可随时安装、更换YSI出品的光学溶解氧、浊度、叶绿素、罗丹明WT和蓝绿藻中的任一传感器，以满足各种应用需求。这是一款使用灵活、操作方便的光学监测仪，既是理想的便携测量仪，又可用于长期野外监测。 YSI 600XLV2/600XLMV2 多参数水质监测仪 YSI 6820/6920型 多参数水质监测仪 YSI 6820EDS/6920EDS型 常规五参数水质 YSI 600XLV2/600XLMV2 多参数水质监测仪，600XLM V2 是6600V2-4的精简型，同样可精确测量电导率、温度、酸碱度/氧化还原电位、水位，但在同一时间只能监测光学溶解氧、浊度、叶绿素、罗丹明WT与蓝绿藻中的一个参数。配有电池室与非散失性内存。为长期现场监测与剖面分析提供了一个低成本方案。 YSI 6920DW/600DW型 饮用水多参数安全监测仪 YSI 600CHL型 叶绿素监测仪 YSI 600CHL型 叶绿素监测仪 YSI 58型 实验室溶解氧测量仪 YSI ProODO 光学溶解氧测量仪YSI ProPlus型 手持式野外/实验室两用测量仪，多种参数选择：溶解氧、BOD、pH、ORP、电导率、氨氮、硝氮、氯化物和温度 YSI 9600型 硝酸盐监测仪 YSI 6500 是水质监控的一种经济有效的选择，有效替代多台单参数设备，可减少安装和操作所需的人力物力 连续监测溶解氧、电导率、温度和酸碱度 YSI 6500与YSI 6系列多参数仪主机连接，可以提供不间断的数据。 YSI 650MDS型 多参数显示和记录系统 用来记录实时数据、校准6系列仪器、设置仪器以及上传数据到计算机等，专为野外使用而设计。YSI 650MDS配有防撞击外壳，符合IP67防水标准，即使掉入水中也能自动浮起。 YSI 600QS可同时测量溶解氧（%空气饱和度和毫克/升浓度）、温度、电导率、酸碱度、氧化还原电位（可选）、深度（可选） YSI 600LS型 高精度水位仪 可精确测量水位、流量、温度和电导率，可与YSI 650MDS、便携式电脑或数据采集平台配合使用。 YSI 600xlm/600xl多参数水质监测仪，各参数为：溶解氧（%空气饱和度与毫克/升浓度）、温度、电导率、比电导度*、盐度*、酸碱度、氧化还原电位、深度或水位、总溶解固体*和电阻率* YSI 600TBD型 浊度监测仪 是在YSI 600OMS光学监测系统平台上，以YSI 6136型 浊度传感器 为核心的浊度监测系统，用于河流、湖泊、池塘、河口及饮用水源水中悬浮固体状况的研究、调查和监测。该监测仪亦可同时测量温度、电导和深度或透气式水位。 YSI 600CHL型 叶绿素监测仪 是在YSI 600OMS光学监测系统平台上，以YSI 6025型 叶绿素传 感器为核心的叶绿素监测系统，用于河流、湖泊、池塘、海洋调查、养殖业、饮用水源、藻类和浮游植物状况的研究、调查和监 测。该监测仪还可同时测量温度、电导和深度或透气式深度。 YSI 6820EDS/6920EDS型 常规五参数水质监测仪 是一个特别设计直接投放在水体中用于长期在线监测的五参数仪。该常规五参数仪既可单独使用，亦可作为水质在线自动监测标准站的五参数仪部分集成到系统中。 YSI 6920DW/600DW型 饮用水多参数安全监测仪 应用于城市自来水供应管网系统中，连续采集水质数据以确认饮用水安全送达社区。 YSI 6820/6920型 多参数水质监测仪 是一个适用于多点采样、长期现场监测与剖面分析的经济型数据记录系统。用户可以自定数据采集的时间间隔期，存储读数可达150,000个。 YSI 6600主导型 多参数水质监测仪，巡测和剖面分析应用的最佳选择 YSI 6600是一款适用于多点采样测量、长期现场监测与剖面分析的多参数仪器，可同时监测多达17个参数。具有90天电池寿命与9组探头结构，其中包括两个供浊度、叶绿素或罗丹明探头同时安装的光学口。操作水深达200米 YSI Level Scout 水位跟踪者 ，透气 或 非透气式 不锈钢 或 钛合金材料 2MB或4MB内存 YSI Level Scout 水位跟踪者 拥有高精度的水位传感器技术，并融合了高精度的压力传感器技术与电源稳定微机电路系统 YSI 556MPS型 多参数水质检测仪，多探头系统成功地结合了便携式仪器与多参数系统的特点，其性能如下： 可同时测量温度、电导、盐度、溶解氧、酸碱度和氧化还原电位以及总溶解固体；所有数据同时显示在屏幕上 YSI 85型 溶解氧、电导、盐度、温度测量仪，3米电缆 YSI 85型 溶解氧、电导、盐度、温度测量仪，7.5米电缆 YSI 85型 溶解氧、电导、盐度、温度测量仪，15米电缆 YSI 85型 溶解氧、电导、盐度、温度测量仪，15米电缆 YSI 85D型 溶解氧、电导、盐度、温度测量仪（不带探头） YSI 55型 溶解氧、温度测量仪 ，手提式操作，亦可肩挂或腰悬 ，不锈钢探头，能抵御更严峻的野外条件；另外，金属的重量让探头更易于沉入水中 ，备有3.7米、7.5米和15米三种电缆长度可供选择 另有低电量显示 YSI 手提式酸度测量仪（60型、63型）是特别为野外测量而设计的专业酸度测量仪器，它克服了一般酸度计电极在野外应用的缺点。 使用特殊电缆屏蔽设计，突破传统酸度计电缆长度的限制，测量水深范围达30米 电极接头全封闭防水，整个探头可插入水中测量 探头加固保护，可抵抗轻度的碰撞 可更换式电极，经济、便于现场维护 ；检测酸度，盐度，电导，温度 YSI 550A 便携式溶氧仪，采用全水密（IP67防水等级）、防撞击仪器外壳，并启用创新性可于野外更换的溶解氧电极模块。使用YSI久经考验的极谱法技术和YSI全球高精密温度典范的热敏电阻法技术，可同时测量溶解氧和温度。新一代PE盖膜提供更快的反应时间和更低的搅拌依赖性。 YSI DO200便携式溶氧，温度测量仪， YSI公司最新推出一系列轻巧、便携式水质测量仪器，以高性价比提供准确的数据。仪器的人机界面友好，操作简单方便（可单手操作）。YSI DO200 可同时测量溶解氧（空气饱和度与毫克/升浓度）与温度。 YSI 58实验室溶解氧测量仪， 系统规格 溶解氧 (%空气饱和度) 测量范围分 辨 率 准 确 度 0至200%空气饱和度 0.1%空气饱和度 ± 0.3%空气饱和度 YSI ProODO 光学溶解氧测量仪 YSI ProPlus型 手持式野外/实验室两用测量仪，多种参数选择：溶解氧、BOD、pH、ORP、电导率、氨氮、硝氮、氯化物和温度 YSI 9600型 硝酸盐监测仪 YSI 6500 连续监测溶解氧、电导率、温度和酸碱度 YSI 6500与YSI 6系列多参数仪主机连接，可以提供不间断的数据。YSI 6500 是水质监控的一种经济有效的选择，有效替代多台单参数设备，可减少安装和操作所需的人力物力。 YSI 650MDS型 多参数显示和记录系统 用来记录实时数据、校准6系列仪器、设置仪器以及上传数据到计算机等，专为野外使用而设计。YSI 650MDS配有防撞击外壳，符合IP67防水标准，即使掉入水中也能自动浮起。

工业分析刚玉坩埚 Alumina Crucible产品名称货号内水坩埚CN11046全水坩埚CN11045四孔坩埚CN11043无孔坩埚CN11044用于5E系列工业分析仪

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat, set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septumfor syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 piecesmulti N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vesselsfor EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)