总氮在线分析仪

Shimadzu 总有机碳分析仪(TOC5000)注射器 体积 描述 注射器货号 替换推杆货号 250µ L 1/4-28 UNF末端 006680 031832 2.5mL 1/4-28 UNF 末端 008680 031854

奥利龙 余氯/总氯/PH分析仪产品参数：余氯总氯测量测量范围：0.01-10ppm重现性: ±3%准确度: ±5%分辨率: 0.01 ppm量间隔：2-10 分钟试试剂指示低于20%，警告试剂缺少水样要求最大压力0.5 bar，pH 4 -10，流速30-40 L/h 流量开关水样压力1 barpH 测量0-10温度测量0-50℃输出8 个 RS485，可选4-20 mA 工作温度1℃ - 45℃电源100-240 V，50-60 Hz尺寸67×33×14 cm（宽× 高× 深）/ 45 kg

波利梅特龙 polymetronORP在线分析仪,poPolymetron 8351ORP氧化还原探头,操作原理,操作规格，说明书：销售热线：15300030867，张经理，欢迎您的来电咨询！ 在氧化还原电极和参比电极组成的测量链的氧化还原系统中，将要测量的电势称为氧化还原电势。它取决于氧化还原系统和转换的电子数量这两部分的活动度比率，在许多情况中溶液的 pH值也会影响电势。Peter的方程式定义了氧化还原电势氧化还原系统的稳定性和可逆性极大地影响被测的氧化还原电势的再现性。 波利梅特龙 polymetronORP在线分析仪,poPolymetron 8351ORP氧化还原探头,操作原理,技术参数 显示范围： - 1500 mV ~ 1500 mV 显示分辨率： 1 mV 测量精度： ± 1.5 mV 重 复 性： ±1 mV 响应时间： 10 秒内 95% 最大温度： 110℃（230?F） 自 检 查： 参比 50 K? 最大压力： 10 bar（145psi）在80℃ 电极体材料： PPS（聚苯硫醚） 电 缆： 10 米PPS 探头体（硫化聚丙烯） 9135 pH和氧化还原变送器，很独特的配置可以满足您的不同需要 机械强度且易于安装：聚酯涂层金属外壳，NEMA 4 ( IP65 ) ，通用型安装支架，适用于墙装，盘装和管道安装 清晰的图像背光显示： - 多种语言显示：英语，法语，德语，意大利语，西班牙语，荷兰语 - 可显示数种单位：pH，mV - 可同时显示测量和相关的温度 - 可显示继电器极限和模拟输出 对校准、编程和维护采用独立的通路(分别带有进入密码) 全部电流隔离： - 传感器与变送器之间 - 微处理器和电源之间，其它电路板和模拟输出之间 2个"智能" 模拟输出：0/4 ~ 20 mA - 线性，双线性或对数模式 - 可模拟环路信号以备检测之用 - 可编程平均值用于快的变化过程 - 4 ~ 20 mA输出功能用于校准，报警和维护之用 用于质量管理的数据检索： - 最后校准的日期和测量值 - 自诊断数据 - 符合规格证书 可选功能： 继电器板 (订货号：p/n. 09125=A=4000 ) - 继电器1：低或高设定点 - 继电器2：低或高设定点 - 继电器3：低或高设定点或系统报警 - 继电器4：低或高设定点或时间输出 继电器输出：250 VAC, 3 A max., 100 VDC, 0,5 A max. RS485主板：串口连接电流隔离 (订货号：p/n. 09125=A=1100 ) 详细的测试证书：(订货号：p/n. 09125=T=0000 )

波利梅特龙Polymetron9135在线pH/ORP分析仪,特点 （销售热线：13718811058，欢迎您的来电咨询，张经理）● 通用性变送器（2个高阻抗输入）：可用于复合电极、pH电极、参比电极、锑电极和氧化还原电极 ● 测量自诊断： 检查pH电极和参比电极的阻抗（专利技术） ● 可用几个通讯输出：2个模拟输出，4个继电器，RS485串口 ● 完整的变送器：脉冲触点或频率输出模式，双向比例功能 ● 校准方法的多种选择： — 自动确认缓冲液的值 — 手动设置过程校准的pH值，以及电极的偏移量和斜率特性波利梅特龙Polymetron9135在线pH/ORP分析仪,波利梅特龙Polymetron9135在线pH/ORP分析仪,参数：技术规格外壳部分符合标准： EN 50081-1 & 50082-2（EMC）欧洲标准： EN 61010-1（低电压）防护标准： NEMA 4X，IP65外壳材料： 铝和聚酯涂层金属外壳，不锈钢螺丝电缆密封： 2*PG13和2*PG11电气连接： 2.5平方毫米端子带螺丝（电源和继电器可拆卸）储藏温度： -20 - +70℃环境温度： -20 - +60℃供电电源： 100 - 240VAC，50/60Hz低 电 压： 13-30VAC，50/60Hz；18-24VDC，功率25W分析技术参数pH ： 量程：0-14pH、分辨率：0.01pH/1mV、重复性：±0.02pH/1mVORP： 量程：±1500mV、分辨率：1mV、重复性：±1mV温度：-20 - +200℃、分辨率：0.1℃、重复性：±0.2℃阻抗设置范围玻璃 ： 5M - 1GΩ参比 ： 1K - 1MΩ模拟输出： 2路0/4-20mA，量程范围可自由编程，1路用做pH或ORP和1路用做温度，2路用做pH或ORP，最大负载900ΩPolymetron9135在线pH/ORP分析仪订货号：序号名称订货号19135PH分析仪9135=A=00002超纯水PH系统08362=A=001039135CPU主板09125=A=100149135测量板09135=A=150059135电源板（标准型）09125=A=200068362PH电极08362=A=200078361PH电极08361=C=00008PH电极3米电缆359016，101109PH电极10米电缆359016，1012010PH电极20米电缆359016，1012211PT100温度探头08362=A=100112PT100的3米电缆08362=A=300113PT100的10米电缆08362=A=300214PT100的20米电缆08362=A=300315PMMA流通池08362=C=4000168350.4PH电极带温度探头08350=C=0004178350.5PH电极带温度探头08350=C=0005188351氧化还原电极08351=C=000019PH4缓冲溶液（500ml/瓶）363130,0050020PH6.88缓冲溶液（500ml/瓶）363131,0050021PH9.22缓冲溶液（500ml/瓶）363132,00500

Shimadzu 岛津总有机碳分析仪(TOC5000)用注射器订货信息：体积描述注射器货号替换推杆货号250μL1/4-28 UNF 末端0066800318322.5mL1/4-28 UNF 末端008680031854

YSI 5000系列实验室BOD分析仪 北京宏昌信科技有限公司销售部 唐海红 13120400643 15321361385 010-59481385 先进的实验室BOD分析仪 YSI 5000系列实验室溶解氧分析仪，配合先进的自搅拌的BOD分析探头和YSI独家拥有的BOD分析软件，实现实验室BOD分析自动化、准确化和标准化。 YSI 5120型 BOD分析软件 · 安装在计算机上，直接驱动溶氧仪，使整个BOD测试过程自动化 · 系统自动存储首、尾天的读数，计算并打印报告 · 当溶解氧读数达到稳定时自动读取并存储读数 · 超饱和样品和温度超越范围警示 · 其它卓越功能包括：自动空白、种样及加荷补偿、非五天测试BOD结果导算，其它稀释度首天读数衍生等 技术参数： 溶解氧（毫克/升）：测量范围 0至60；分辨率 0.01；准确度 ± 0.1%+1lsd 溶解氧（%空气饱和度）：测量范围 0至600%；分辨率 0.1%；准确度 ± 0.1% +1lsd 温度：测量范围 -5至+50℃；分辨率 0.1℃；准确度 ± 0.1℃ 主要特点： · 传统的BOD 稀释测试法，5000系列仪器配合YSI的溶解氧/BOD探头，仪器整体符合国标HJ/T99-2003标准，溶解氧测量符合国标电化学探头法GB11913-89标准，BOD测量完全符合国标GB7488-87标准 · 极其先进的实验室溶氧仪＋自搅拌BOD探头方法（BOD分析软件） · 自动搅拌BOD 电极，单手即可操作 · 可选配BOD分析软件，实现BOD测试自动化，实现数据自动存储BOD自动计算，并打印报告；超饱和样品和温度超越范围警示 · 可实现快速大批量测试 · 搅拌力强，确保测试数据准确 · 搅拌速率恒定，再现性佳 · 内置搅拌器，无需另加搅拌工具，省时，方便 · 使用5906型盖膜：预置已预张的渗透膜，免除安装不当的人为误差 · 无零漂，免调零 · 膜完整性监测，当膜破损时仪器自动警示 · 可存储100组带日期、时间标签的读数 北京宏昌信科技有限公司销售部 唐海红 13120400643 15321361385 010-59481385 YSI 6820V2 / 6920V2型 多参数水质监测仪 YSI 6600V2型 多参数水质监测仪 YSI 600OMS V2 光学监测仪 ，YSI 600OMS V2 光学监测仪 外形小巧、轻便耐固、耗电低，一个光学端口，可随时安装、更换YSI出品的光学溶解氧、浊度、叶绿素、罗丹明WT和蓝绿藻中的任一传感器，以满足各种应用需求。这是一款使用灵活、操作方便的光学监测仪，既是理想的便携测量仪，又可用于长期野外监测。 YSI 600XLV2/600XLMV2 多参数水质监测仪 YSI 6820/6920型 多参数水质监测仪 YSI 6820EDS/6920EDS型 常规五参数水质 YSI 600XLV2/600XLMV2 多参数水质监测仪，600XLM V2 是6600V2-4的精简型，同样可精确测量电导率、温度、酸碱度/氧化还原电位、水位，但在同一时间只能监测光学溶解氧、浊度、叶绿素、罗丹明WT与蓝绿藻中的一个参数。配有电池室与非散失性内存。为长期现场监测与剖面分析提供了一个低成本方案。 YSI 6920DW/600DW型 饮用水多参数安全监测仪 YSI 600CHL型 叶绿素监测仪 YSI 600CHL型 叶绿素监测仪 YSI 58型 实验室溶解氧测量仪 YSI ProODO 光学溶解氧测量仪YSI ProPlus型 手持式野外/实验室两用测量仪，多种参数选择：溶解氧、BOD、pH、ORP、电导率、氨氮、硝氮、氯化物和温度 YSI 9600型 硝酸盐监测仪 YSI 6500 是水质监控的一种经济有效的选择，有效替代多台单参数设备，可减少安装和操作所需的人力物力 连续监测溶解氧、电导率、温度和酸碱度 YSI 6500与YSI 6系列多参数仪主机连接，可以提供不间断的数据。 YSI 650MDS型 多参数显示和记录系统 用来记录实时数据、校准6系列仪器、设置仪器以及上传数据到计算机等，专为野外使用而设计。YSI 650MDS配有防撞击外壳，符合IP67防水标准，即使掉入水中也能自动浮起。 YSI 600QS可同时测量溶解氧（%空气饱和度和毫克/升浓度）、温度、电导率、酸碱度、氧化还原电位（可选）、深度（可选） YSI 600LS型 高精度水位仪 可精确测量水位、流量、温度和电导率，可与YSI 650MDS、便携式电脑或数据采集平台配合使用。 YSI 600xlm/600xl多参数水质监测仪，各参数为：溶解氧（%空气饱和度与毫克/升浓度）、温度、电导率、比电导度*、盐度*、酸碱度、氧化还原电位、深度或水位、总溶解固体*和电阻率* YSI 600TBD型 浊度监测仪 是在YSI 600OMS光学监测系统平台上，以YSI 6136型 浊度传感器 为核心的浊度监测系统，用于河流、湖泊、池塘、河口及饮用水源水中悬浮固体状况的研究、调查和监测。该监测仪亦可同时测量温度、电导和深度或透气式水位。 YSI 600CHL型 叶绿素监测仪 是在YSI 600OMS光学监测系统平台上，以YSI 6025型 叶绿素传 感器为核心的叶绿素监测系统，用于河流、湖泊、池塘、海洋调查、养殖业、饮用水源、藻类和浮游植物状况的研究、调查和监 测。该监测仪还可同时测量温度、电导和深度或透气式深度。 YSI 6820EDS/6920EDS型 常规五参数水质监测仪 是一个特别设计直接投放在水体中用于长期在线监测的五参数仪。该常规五参数仪既可单独使用，亦可作为水质在线自动监测标准站的五参数仪部分集成到系统中。 YSI 6920DW/600DW型 饮用水多参数安全监测仪 应用于城市自来水供应管网系统中，连续采集水质数据以确认饮用水安全送达社区。 YSI 6820/6920型 多参数水质监测仪 是一个适用于多点采样、长期现场监测与剖面分析的经济型数据记录系统。用户可以自定数据采集的时间间隔期，存储读数可达150,000个。 YSI 6600主导型 多参数水质监测仪，巡测和剖面分析应用的最佳选择 YSI 6600是一款适用于多点采样测量、长期现场监测与剖面分析的多参数仪器，可同时监测多达17个参数。具有90天电池寿命与9组探头结构，其中包括两个供浊度、叶绿素或罗丹明探头同时安装的光学口。操作水深达200米 YSI Level Scout 水位跟踪者 ，透气 或 非透气式 不锈钢 或 钛合金材料 2MB或4MB内存 YSI Level Scout 水位跟踪者 拥有高精度的水位传感器技术，并融合了高精度的压力传感器技术与电源稳定微机电路系统 YSI 556MPS型 多参数水质检测仪，多探头系统成功地结合了便携式仪器与多参数系统的特点，其性能如下： 可同时测量温度、电导、盐度、溶解氧、酸碱度和氧化还原电位以及总溶解固体；所有数据同时显示在屏幕上 YSI 85型 溶解氧、电导、盐度、温度测量仪，3米电缆 YSI 85型 溶解氧、电导、盐度、温度测量仪，7.5米电缆 YSI 85型 溶解氧、电导、盐度、温度测量仪，15米电缆 YSI 85型 溶解氧、电导、盐度、温度测量仪，15米电缆 YSI 85D型 溶解氧、电导、盐度、温度测量仪（不带探头） YSI 55型 溶解氧、温度测量仪 ，手提式操作，亦可肩挂或腰悬 ，不锈钢探头，能抵御更严峻的野外条件；另外，金属的重量让探头更易于沉入水中 ，备有3.7米、7.5米和15米三种电缆长度可供选择 另有低电量显示 YSI 手提式酸度测量仪（60型、63型）是特别为野外测量而设计的专业酸度测量仪器，它克服了一般酸度计电极在野外应用的缺点。 使用特殊电缆屏蔽设计，突破传统酸度计电缆长度的限制，测量水深范围达30米 电极接头全封闭防水，整个探头可插入水中测量 探头加固保护，可抵抗轻度的碰撞 可更换式电极，经济、便于现场维护 ；检测酸度，盐度，电导，温度 YSI 550A 便携式溶氧仪，采用全水密（IP67防水等级）、防撞击仪器外壳，并启用创新性可于野外更换的溶解氧电极模块。使用YSI久经考验的极谱法技术和YSI全球高精密温度典范的热敏电阻法技术，可同时测量溶解氧和温度。新一代PE盖膜提供更快的反应时间和更低的搅拌依赖性。 YSI DO200便携式溶氧，温度测量仪， YSI公司最新推出一系列轻巧、便携式水质测量仪器，以高性价比提供准确的数据。仪器的人机界面友好，操作简单方便（可单手操作）。YSI DO200 可同时测量溶解氧（空气饱和度与毫克/升浓度）与温度。 YSI 58实验室溶解氧测量仪， 系统规格 溶解氧 (%空气饱和度) 测量范围分 辨 率 准 确 度 0至200%空气饱和度 0.1%空气饱和度 ± 0.3%空气饱和度 YSI ProODO 光学溶解氧测量仪 YSI ProPlus型 手持式野外/实验室两用测量仪，多种参数选择：溶解氧、BOD、pH、ORP、电导率、氨氮、硝氮、氯化物和温度 YSI 9600型 硝酸盐监测仪 YSI 6500 连续监测溶解氧、电导率、温度和酸碱度 YSI 6500与YSI 6系列多参数仪主机连接，可以提供不间断的数据。YSI 6500 是水质监控的一种经济有效的选择，有效替代多台单参数设备，可减少安装和操作所需的人力物力。 YSI 650MDS型 多参数显示和记录系统 用来记录实时数据、校准6系列仪器、设置仪器以及上传数据到计算机等，专为野外使用而设计。YSI 650MDS配有防撞击外壳，符合IP67防水标准，即使掉入水中也能自动浮起。

自动牛奶分析仪配件是一种对牛奶成分分析的一种仪器，能快速对乳制品成分进行检测，它是一款价格较低的自动牛奶检测仪。 自动牛奶分析仪配件应用 用于快速检测生鲜乳的多种成分含量，包括：脂肪、蛋白质、非脂乳固体、乳糖、密度、含水率、冰点、电导率、灰分、样品温度等,无需任何化学试剂和辅助设施，操作极为简单，快速、准确地检测出样品中各种成分的含量 适用于奶站、牧场、企业和畜牧兽医站等部门对乳品的检测范围。自动牛奶分析仪配件参数 脂肪：0.01% -25% 非脂乳固体3% -15% 密度：1015 –1040kg/m3， 蛋白质：2% -7%， 乳糖：0.01% -6% 掺水：0% -70% 牛奶温度：1°C –40°C 冰点：-0.400 –0.700°C 盐分：0.4 –1.5% PH：0-14 电导：3-14mS/cm 总固体：0-25% 自动牛奶分析仪配件特点●带蠕动泵，自动清洗 ●安装、操作、维护、校准方便简单。 ●便携式设计紧凑，可用于车载。 ●只需少量牛奶，便可取得精确结果。 ●低功耗，不使用有害化学物质 ●自带RS232接口，方便与计算机连接。 ●内置打印机，实现数据同步打印。 ●两个样本自我校准 ●检测速度：≥60个样品/小时 孚光精仪是全球领先的进口科学仪器和实验室仪器领导品牌服务商，产品技术和性能保持全球领先,拥有牛奶分析仪,食品分析仪在内的全球最为齐全的实验室和科学仪器品类，世界一流的生产工厂和极为苛刻严谨的质量控制体系，确保每个产品是用户满意的完美产品。我们海外工厂拥有超过3000种仪器的大型现代化仓库，可在下单后12小时内从国外直接空运发货，我们位于天津保税区的进口公司众邦企业（天津)国际贸易公司为客户提供全球零延误的进口通关服务。更多关于自动牛奶分析仪价格等诸多信息，孚光精仪会在第一时间更新并呈现出来，了解更多内容请关注孚光精仪官方网站方便获取！

硝酸盐探头就要与便携式水质分析仪/水质监测仪相连接，主要监测水质里面的硝酸盐的含量便携式多参数水质监测仪，多参数水质分析仪，便携式水质监测仪，便携式水质分析仪，AP-2000多参数水质分析仪，AP-7000在线水质监测仪，英国Aquaread水质监测仪，AP-800便携式多参数水质测定仪，AP-700野外便携式多参数水质监测仪，AP-2000 GPS便携式水质多参数监测仪，便携式多参数水质监测仪，可以现场测量水体温度、深度、pH、氧化还原电位、溶解氧、电导率、TDS、盐度、电阻等水质多参数指标, 同时记录时间和位置信息。AP-2000可增配一个ISE电极（铵离子 氨氮 氯离子 氟化物 硝酸盐 钙）和一个光学探头（叶绿素 蓝藻 浊度 水中油）可更换成其他参数等水质多参数指标，均有温度自动补偿功能. 便携式多参数水质监测仪中国总代理：南京铭奥仪器设备有限公司 便携式多参数水质监测仪水质传感器参数范围分辨率准确率溶解氧0-500%/0-50.00mg/L0.1%/0.01mg/L0.01 mg/L电导率0–200mS/cm (200,000μS/cm)0.1μS/cm± 0.5%总溶解固体量0 – 100,000 mg/L (ppm)两个自动确定的量程：0 – 9999mg/L,10.00 – 100.00g/L+1%读数或+0.1单位，取两者中的较大值电阻率5Ωcm – 1MΩcm两个自动确定的量程：5 – 9999Ωcm10.0 – 1000.0KΩcm+1%读数或+0.1单位，取两者中的较大值盐度0 -70 PSU / 0 –70 ppt (g/Kg)0.01 PSU / 0.01 ppt+1%读数或+0.1单位，取两者中的较大值海水比重0 – 50 σt0.1 σt± 1.0 σt氧化还原电位± 2000Mv0.1Mv± 0.5Mv水深度0 – 30M(0 – 100F)0.01M(0.01F)+/- 0.1M(+/- 4”)水温-5°C至+50°C (23°F 至122°F)0.1°C/F± 0.5°CPH值0 – 14 pH / ± 625mV0.01 pH / ± 0.1mV± 0.01 pH / ± 0.5mV可选离子传感器氨氮0–1,000mg/L (ppm)两个自动确定的量程：0.00-99.99 mg/L, 100.0–999.9 mg/L± 10%硝酸盐0–1,000mg/L (ppm)两个自动确定的量程：0.00-99.99 mg/L, 100.0–999.9 mg/L± 10%氯化物0–1,000mg/L (ppm)两个自动确定的量程：0.00-99.99 mg/L, 100.0–999.9 mg/L± 10%氟化物0–1,000mg/L (ppm)两个自动确定的量程：0.00-99.99 mg/L, 100.0–999.9 mg/L± 10%钙0–1,000mg/L (ppm)两个自动确定的量程：0.00-99.99 mg/L, 100.0–999.9 mg/L± 10%可选光学传感器叶绿素 A0–500 μg/L (ppb)0.1 μg/L± 2%浅水蓝绿藻0–300,000 cells/mL1 cell/mL± 2%海水蓝绿藻0–200,000 cells/mL1 cell/mL± 2%若丹明0–500 μg/L (ppb)0.1 μg/L± 5%荧光染料0–500 μg/L (ppb)0.1 μg/L± 5%成品油0–10,000 μg/L (ppb)0.1 μg/L± 2%浊度0–3000 NTU0.1NTU± 2%

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat, set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septumfor syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 piecesmulti N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vesselsfor EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat, set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septumfor syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 piecesmulti N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vesselsfor EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat, set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septumfor syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 piecesmulti N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vesselsfor EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)