在线总磷分析仪原理

波利梅特龙 polymetronORP在线分析仪,poPolymetron 8351ORP氧化还原探头,操作原理,操作规格，说明书：销售热线：15300030867，张经理，欢迎您的来电咨询！ 在氧化还原电极和参比电极组成的测量链的氧化还原系统中，将要测量的电势称为氧化还原电势。它取决于氧化还原系统和转换的电子数量这两部分的活动度比率，在许多情况中溶液的 pH值也会影响电势。Peter的方程式定义了氧化还原电势氧化还原系统的稳定性和可逆性极大地影响被测的氧化还原电势的再现性。 波利梅特龙 polymetronORP在线分析仪,poPolymetron 8351ORP氧化还原探头,操作原理,技术参数 显示范围： - 1500 mV ~ 1500 mV 显示分辨率： 1 mV 测量精度： ± 1.5 mV 重 复 性： ±1 mV 响应时间： 10 秒内 95% 最大温度： 110℃（230?F） 自 检 查： 参比 50 K? 最大压力： 10 bar（145psi）在80℃ 电极体材料： PPS（聚苯硫醚） 电 缆： 10 米PPS 探头体（硫化聚丙烯） 9135 pH和氧化还原变送器，很独特的配置可以满足您的不同需要 机械强度且易于安装：聚酯涂层金属外壳，NEMA 4 ( IP65 ) ，通用型安装支架，适用于墙装，盘装和管道安装 清晰的图像背光显示： - 多种语言显示：英语，法语，德语，意大利语，西班牙语，荷兰语 - 可显示数种单位：pH，mV - 可同时显示测量和相关的温度 - 可显示继电器极限和模拟输出 对校准、编程和维护采用独立的通路(分别带有进入密码) 全部电流隔离： - 传感器与变送器之间 - 微处理器和电源之间，其它电路板和模拟输出之间 2个"智能" 模拟输出：0/4 ~ 20 mA - 线性，双线性或对数模式 - 可模拟环路信号以备检测之用 - 可编程平均值用于快的变化过程 - 4 ~ 20 mA输出功能用于校准，报警和维护之用 用于质量管理的数据检索： - 最后校准的日期和测量值 - 自诊断数据 - 符合规格证书 可选功能： 继电器板 (订货号：p/n. 09125=A=4000 ) - 继电器1：低或高设定点 - 继电器2：低或高设定点 - 继电器3：低或高设定点或系统报警 - 继电器4：低或高设定点或时间输出 继电器输出：250 VAC, 3 A max., 100 VDC, 0,5 A max. RS485主板：串口连接电流隔离 (订货号：p/n. 09125=A=1100 ) 详细的测试证书：(订货号：p/n. 09125=T=0000 )

奥利龙 余氯/总氯/PH分析仪产品参数：余氯总氯测量测量范围：0.01-10ppm重现性: ±3%准确度: ±5%分辨率: 0.01 ppm量间隔：2-10 分钟试试剂指示低于20%，警告试剂缺少水样要求最大压力0.5 bar，pH 4 -10，流速30-40 L/h 流量开关水样压力1 barpH 测量0-10温度测量0-50℃输出8 个 RS485，可选4-20 mA 工作温度1℃ - 45℃电源100-240 V，50-60 Hz尺寸67×33×14 cm（宽× 高× 深）/ 45 kg

Shimadzu 总有机碳分析仪(TOC5000)注射器 体积 描述 注射器货号 替换推杆货号 250µ L 1/4-28 UNF末端 006680 031832 2.5mL 1/4-28 UNF 末端 008680 031854

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

SMS 100汞分析仪的详细资料： 详情请联系吴小姐：15080317079 PerkinElmer SMS 100汞分析仪 能够直接对固体样品进行分析的汞分析仪 SMS 100是一款专用汞分析仪，运用热分解、汞融合以及美国环境保护协会方法7473中所描述的原子吸收原理来测定固体及液体样品中的总汞含量。 与传统溶液分析系统使用的化学还原步骤不同的是，SMS 100使用分解炉来释放出汞蒸气。这样，无论是固体还是液体样品都可以直接放入仪器的自动进样器中，无需消解或样品前处理就可以进行分析。此方法不需要将汞转变成汞离子，所以大大节省了样品前处理步骤。对用户而言，直接的好处就是缩短分析时间，同时减少了化学试剂的使用，从而使得它与传统汞分析仪相比，分析成本明显降低。适用的样品包括淤泥、沉积物、土壤、废水、污水、煤、飞尘、矿物、矿石、化肥、各种粮食、血液、尿以及头发等。 特征与优势 Ø 无需制备样品 Ø 特别低的检出限 Ø 全自动处理 Ø 易于维护 SMS 100自动汞分析仪 110V/60Hz N9309000 SMS 100自动汞分析仪 220V/50Hz N9309001 SMS 100耗材 基本备件N9309109 扩展备件N9309110 镍舟 数量42 N9309017 石英舟 数量10个N9309032 碳粉 500g N9309035 催化管 (包) N9309036 自动进样舟N9309019 排气组件N9309006 混合管N9309007 汞灯N9309010 碳材料汞蒸气收集器N9309011 Nafion.干燥管N9309021 Chromosorb. 250mL N9309103 汞储存溶液100ppm N9309106 备件基本备件N9309109 包括： 混合管N9309007 汞灯N9309010 Nafion.干燥管N9309021 O形圈N9309029 扩展备件N9309110 包括： 混合管N9309007 气路组件N9309008 汞灯N9309010 进样叉组件N9309012 CVAAS管线N9309013 混汞机加热线圈N9309066 6g Krytox.管润滑脂N9309108 Nafion.干燥管N9309021 石英窗N9309024 O形圈N9309029 窗口端盖N9309031 5英寸光电池N9309033 1英寸光电池N9309034

波利梅特龙Polymetron8810在线氯离子分析仪特点 ● 不需要样品过滤（当悬浮颗粒1%或1mm） ● 容易操作和设定 ● 自动温度补偿 ● 每一个测量周期后，自动反应器清洗 ● 每月一次维护销售热线：13718811058，张经理波利梅特龙Polymetron8810在线氯离子分析仪简介：波利梅特龙Polymetron8810在线氯离子分析仪原理氯离子选择电极 首先，排放阀和清洗阀同时打开，允许清洗液在设定的时间里清洗反应池（如图）。 当清洗阀关闭后，样品阀打开；这是排放阀继续开启几秒钟，让样品水冲洗掉残留的清洗液滴。然后，排放阀关闭，内置的虹吸管自动调整样品体积。这时候，搅拌泵激活，在程序设定的时间内工作。最后离子选择电位和离子浓度的数值显示出来。 根据能斯特定律：E=E0 + SlogCV1：清洗阀； V2：样品阀； V3：排放阀； P1：试剂泵； P4：自动校准泵； D：排放管； E：电极/Pt100 M： 搅拌棒； S：虹吸管； MV：反应池； K：电极电缆波利梅特龙Polymetron8810在线氯离子分析仪,技术参数测量范围：0.5-500mg/L CL-（高浓度采用稀释方法）检测下限：0.5mg/L分析周期：可编程：1个周期/5min，最长时间999分钟样品通道：购置8811样品序列器，可以选择1-6个样品进样检测次序：多流路循环检测，或遵照程序设定检测次序水样参数：温度：0-50℃； 压力：0.5-6bar； 流速：50-300L/h清洗液压力：1-6bar清洗液流速：50-300L/h水样稀释：可编程安装方式：面板式安装：约25Kg； 壁挂式安装：约50Kg； 独立柜安装：小于100Kg电源功耗：220VAC/50-60Hz；100VA水管尺寸：样品管：12/14mm；清洗液管：6/8mm； 仪器空气：4/6mm仪器气源：4-7bar，经过过滤的气体重量尺寸：面板式安装：约25Kg； 壁挂式安装：约50Kg； 独立柜安装：小于100Kg；见仪表尺寸图工作电极：氯离子选择电极，PT100温度电极环境温度：5-55℃测量试剂：通常3-6ml/周期，根据测量周期决定试剂消耗量，用户自己配置试剂测量数据：浓度单位：mg/L，ppm；准确度±2%；再现性±3%防护等级：IP65LCD显示 ：数字：4个数字，高度为17.8mm；文字：2行，16个字符，高度为5.86mm系统校准：手动系统校准（两个标准溶液）；自动校准系统（可选）模拟输出：2路0/4-20mA继 电 器：3路继电器：1路系统报警，2路高限值或低限值警报控制功能：1路水样/稀释液位检测器，1路试剂液位检测器，1路校准溶液液位检测器，RS232接口，远程启动/停止 波利梅特龙Polymetron8810在线氯离子分析仪,订货号：基本配置P/N368810,31220： 8810氯离子分析仪，19"面板安装型包括：试剂添加模块，氯离子选择电极/温度参考电极PT100，试剂泵可选备件368810,71050：自动校正系统（建议订购）368810,56000：化学清洗系统08810=A=5300：自动稀释模块，当氯离子浓度超过500mg/L368810,76000：自动加热模块/控制器368810,65000：手动加热模块/控制器368810,40000：玻璃纤维机箱，墙装型368810,45000：钢质机箱，立式安装型368810,93001：两年用备件多通道样品序列器08810=A=2032：双通道样品序列器08810=A=2033：三通道样品序列器08810=A=2034：四通道样品序列器08810=A=2035：五通道样品序列器08810=A=2036：六通道样品序列器波利梅特龙Polymetron8810在线氯离子分析仪,波利梅特龙Polymetron8810在线氯离子分析仪

纳米颗粒分析仪配件用于观测和分析液体中的微小颗粒的布朗运动速率与尺寸分布相关，采用纳米颗粒跟踪分析（NTA）技术，通过激光散射装置（纳米观测）与超显微镜ultra-microscope和NTA软件的相结合，生成纳米颗粒图像，是全球领先的纳米粒度分析仪。纳米颗粒分析仪配件 纳米观测原理 纳米颗粒分析仪使用纳米透视Nano-Insight 激光散射模块，可以通过顶眼超显微镜观测到液体中的纳米粒子。采用不同激光散射颗粒在矩阵中表现为模糊点。模糊点根据其各自的布朗运动而移动。液体中有不同的布朗运动粒子。小粒子比大粒子受到相邻粒子的影响更少。因此，在超显微图像中，较大的粒子有大的模糊外观。 NTA能够追踪粒子的相应路径。 纳米观测模块 纳米观测模块的设计，可以使其安装在超显微镜，顶眼纳米的底板。可以通过Mishell软件来控制该模块。Mishell软件控制着纳米观测模块以及照相机。根据应用决定在纳米观测模块装备一个或多个激光器。激光器以一种特殊的方式排列。左侧图片上展示的是纳米观测图。较小的粒子比较大的粒子移动更快。我们用摄像机同时跟踪每个粒子。 顶眼超显微镜 顶眼超显微镜将进入模糊点的散射光可视化。用适当的时间分辨跟踪，模糊云可被分配并与各自的粒径相关。粒子的布朗运动图像是唯一的。下面将给出例子。每个模糊点代表单个粒子。 NTA 软件 上图展示的是NTA分析的典型图像。散射激光被捕获到模糊点，要根据时间函数跟踪模糊点。我们跟踪每个模糊点。跟踪每个粒子的方法，得到的技术结果是高分辨率。我们正在寻找与图像相关的量，当我们知道相关的量后，我们就可以极其精确地确定各种粒子的浓度。该技术将会带起许多可能的应用。例如，可能也可以使用荧光激光器。使用荧光激光器，可以瞄准复杂的基质里的一个粒子。该技术带来的好处是，用户可以在视觉上检查并且通过观察相应图像验证所有可能的应用。 MiNan是Mishell® 内的一个模块- 扩展图像分析软件包，被认为是市场上最先进的图像分析软件。MiNan是一个子程序，可以进行Morphious纳米粒子分析的全部描述。 MiNan是自带Morphious纳米系统的软件，研发用于纳米粒子的可视化以及纳米粒子的大小、形状（形态）和浓度的测量。每个粒子是一个个体，但通过观测扩散同时被分析。这种一个粒子后接一个粒子的方法产生高分辨率的结果，即粒子的尺寸分布和浓度分辨率高，同时视觉验证让用户对数据有了额外的信心。当荧光模式检测标记粒子时，粒子尺寸和浓度，蛋白质聚集和粘度都可以被分析。 纳米颗粒分析仪配件应用 ? 在制药或复合产业研发药物 ? 用于病毒筛查 ? 用于开发纳米生物标记物或毒物筛查 ? 用于蛋白质聚集的动力学模型研究 ? 用于通过膜泡的表征研究疾病 ? 用于促进纳米复合材料的发展 纳米颗粒分析仪配件特色 ? 在同一时间多粒子高通量表征 ? 实时视觉展示粒子，允许用户评估试验，无需额外复杂性 ? 方便和易于使用的软件，允许用户通过宏设置任何实验 ? 添加像高通量自动采样器，泵或加热和制冷配件 ? 自适应模块化系统构建任何复杂的应用程序，操作轻松舒适 ? 超级高效和购买成本低 ? 该系统提供高分辨率的粒度特性来研究复杂的多分散矩阵 ? 激光波长可选择 ? 通过给过滤器添加电动轮，得到自适应荧光分析 纳米颗粒分析仪配件参数 ? 尺寸 10 nm - 2000 nm* ? 浓度 106 - 109 粒子/ mL ? 荧光检测 纳米颗粒分析仪配件规格 温度范围 15-40 °C 电源 230V AC/115V AC, 50/60 Hz 摄像机 USB3 CMOS分辨率：1936x1216 161帧/秒，像素尺寸5.86μm：颜色校准模块 功耗 18W 激光波长 405nm（紫色），488nm（蓝），532nm（绿），642nm（红色） 尺寸范围 从10 nm到2000 nm (取决于材料) 焦点 电脑控制电动调焦 个人计算机 SDD亿康 II SDSSDHII-120G-G25HDD 西数蓝WD10EZEX1 TB|主板千兆字节 GA-Z97X-UD3H|内存金士顿骇客神条怒黑| HX318C10FBK2/1616 GB DDR3-RAM 处理器 英特尔® 酷睿™ i7 i7-4790K四核4×4.0 GHz 显卡 PNY VCQK2200-PB 4GB 电源 酷冷至尊 G750M 750w 机箱 酷冷至尊黑 软件 Windows® ＆（或更高）.由Mishell® 供电 Mishell是Microptik BV公司的注册商标。 Windows是微软公司的注册商标。 MiNan尖端程序在Mishell下运行，以充分体现由Morphious纳米获得的纳米粒子 尺寸（长×宽×高） 20 x 18 x 30 cm 重量 10.5 kg

【供应德国WTW Multi 350i多功能水质分析仪,Multi 350i多功能水质分析仪价格,厂家，简单介绍】供应德国WTW Multi 350i多功能水质分析仪,Multi 350i多功能水质分析仪价格,厂家,多功能水质分析仪,便携式水质分析仪,新型水质分析仪,最大优势在于可同时测量显示pH，溶氧，电导率和温度这4个参数 北京宏昌信科技有限公司联系人：张经理电话；010-82752485-815 13718811058 15300030867【供应德国WTW Multi 350i多功能水质分析仪,Multi 350i多功能水质分析仪价格,厂家，详细说明】 德国WTW水质分析仪,多功能水质分析仪,便携式水质分析仪,新型水质分析仪,最大优势在于可同时测量显示pH，溶氧，电导率和温度这4个参数 供应德国WTW Multi 350i多功能水质分析仪,Multi 350i多功能水质分析仪价格,厂家 供应德国WTW Multi 350i多功能水质分析仪,Multi 350i多功能水质分析仪价格,厂家 ，特性： 同时显示所有参数 功能齐全，易于扩展 测试准确 可作离子测试 Multi350i是WTW最新推出的手提式测试仪器，它的最大优势在于可同时测量显示pH，溶氧，电导率和温度这4个参数。此外，该仪器还内置离子浓度测试功能，只要接上相应的离子选择电极便可实现离子浓度测试。Multi350i可兼容目前WTW的所有实验室电极。该仪器采用菜单式操作，具大尺寸背光显示屏，可存储1800组测试数据。它采用省电设计，内置优质 NiMH充电电池，连续使用时间可达1000小时。 供应德国WTW Multi 350i多功能水质分析仪,Multi 350i多功能水质分析仪价格,厂家 ，配套使用的电极： 新型ConOx 电极：溶氧和电导电极合二为一 供应德国WTW Multi 350i多功能水质分析仪,Multi 350i多功能水质分析仪价格,厂家 ，特点： 同时测试溶氧、电导率和温度 携带方便 细长构造 一次填充可用6个月，无零点电流 跟Multi 350i配套使用的是WTW最新款的ConOx电极，该电极可同时测试电导率和溶氧这两个数值，可轻易实现溶氧测试的自动盐度补偿。可以说，WTW的溶氧测试在世界上处于领先水平，它可实现自动温度、自动压力和自动盐度补偿，可实现准确的溶氧测试。ConOx电极的特殊性还在于溶氧测试模块可随时拆下来。从测试原理上说，溶氧采用了历经考验，可靠耐用的Galvanic法，不需极化，马上就可测试；而电导率采用的是四极式测试原理，该原理具有测试准确，耐污染和沾污，易于清洗的优点。电缆线长度可选，有1.5m, 3m和6m。

波利梅特龙polymetron9211在线磷表/哈希211在线磷表,操作说明书，特点，办事处，现货，促销：销售热线，15300030867，张经理，欢迎您的来电咨询！● 多通道操作（1～6）● 极低的运行成本● 运行维护量小● 自动操作系统的水厂可选远程控制● 简单友好的用户编程系统● 内置数据记录仪● 自动两点校准（化学零点和斜率）波利梅特龙polymetron9211在线磷表/哈希211在线磷表,操作说明书，特点，办事处，现货，操作原理样水通过样水选择电磁阀进入仪表，每路样水的流量都能通过针型阀调节。在一路样水进入测量池之前，它有足够的流动时间来冲洗整个水路和溢流槽。然后，样水阀打开，样水进入测量池。一旦测量池被冲洗完毕并且充满样水，样水阀关闭，并顺序注入试剂。 可以用两个不同的方法：a) 测量范围： 钒酸盐方法：0～50 ppm PO4称做“黄色钼钒酸盐” 法试剂1：浓硫酸+ 二水合钼酸钠+ 偏钒酸铵b) 测量范围： 钼酸盐方法：0～5 ppm PO4称做“蓝色ANSA”法试剂1：浓硫酸+ 二水合钼酸钠试剂2：1-氨基-2 奈酚- 4 硫酸（ANSA）+ 偏硫酸二钠+ 亚硫酸钠

波利梅特龙Polymetron9135在线pH/ORP分析仪,特点 （销售热线：13718811058，欢迎您的来电咨询，张经理）● 通用性变送器（2个高阻抗输入）：可用于复合电极、pH电极、参比电极、锑电极和氧化还原电极 ● 测量自诊断： 检查pH电极和参比电极的阻抗（专利技术） ● 可用几个通讯输出：2个模拟输出，4个继电器，RS485串口 ● 完整的变送器：脉冲触点或频率输出模式，双向比例功能 ● 校准方法的多种选择： — 自动确认缓冲液的值 — 手动设置过程校准的pH值，以及电极的偏移量和斜率特性波利梅特龙Polymetron9135在线pH/ORP分析仪,波利梅特龙Polymetron9135在线pH/ORP分析仪,参数：技术规格外壳部分符合标准： EN 50081-1 & 50082-2（EMC）欧洲标准： EN 61010-1（低电压）防护标准： NEMA 4X，IP65外壳材料： 铝和聚酯涂层金属外壳，不锈钢螺丝电缆密封： 2*PG13和2*PG11电气连接： 2.5平方毫米端子带螺丝（电源和继电器可拆卸）储藏温度： -20 - +70℃环境温度： -20 - +60℃供电电源： 100 - 240VAC，50/60Hz低 电 压： 13-30VAC，50/60Hz；18-24VDC，功率25W分析技术参数pH ： 量程：0-14pH、分辨率：0.01pH/1mV、重复性：±0.02pH/1mVORP： 量程：±1500mV、分辨率：1mV、重复性：±1mV温度：-20 - +200℃、分辨率：0.1℃、重复性：±0.2℃阻抗设置范围玻璃 ： 5M - 1GΩ参比 ： 1K - 1MΩ模拟输出： 2路0/4-20mA，量程范围可自由编程，1路用做pH或ORP和1路用做温度，2路用做pH或ORP，最大负载900ΩPolymetron9135在线pH/ORP分析仪订货号：序号名称订货号19135PH分析仪9135=A=00002超纯水PH系统08362=A=001039135CPU主板09125=A=100149135测量板09135=A=150059135电源板（标准型）09125=A=200068362PH电极08362=A=200078361PH电极08361=C=00008PH电极3米电缆359016，101109PH电极10米电缆359016，1012010PH电极20米电缆359016，1012211PT100温度探头08362=A=100112PT100的3米电缆08362=A=300113PT100的10米电缆08362=A=300214PT100的20米电缆08362=A=300315PMMA流通池08362=C=4000168350.4PH电极带温度探头08350=C=0004178350.5PH电极带温度探头08350=C=0005188351氧化还原电极08351=C=000019PH4缓冲溶液（500ml/瓶）363130,0050020PH6.88缓冲溶液（500ml/瓶）363131,0050021PH9.22缓冲溶液（500ml/瓶）363132,00500

Shimadzu 岛津总有机碳分析仪(TOC5000)用注射器订货信息：体积描述注射器货号替换推杆货号250μL1/4-28 UNF 末端0066800318322.5mL1/4-28 UNF 末端008680031854

英国PPM公司PPM-HTV便携式泵吸甲醛检测分析仪，精度：0.01ppm，说明书，办事处，总代，代理，促销，特点，操作，步骤，说明书，现货：销售热线：15300030867,13718811058，张经理，欢迎您的来电咨询！　　以ppm和mg/m3为单位显示甲醛浓度　　不受高湿度和温度影响，具备补偿功能　　标准配置包括一支甲醛校正源(有效期半年)和操作手册，只需数秒钟就能完成校准程序　　单键操作，能够快速采样。快速恢复时间 　　选配的PC遥控软件用于记录数据及实时监测　　已获ISO9001：2000质量认证，并符合CE标准，使设备长时间无故障运行英国PPM公司PPM-HTV便携式泵吸甲醛检测分析仪，精度：0.01ppm，说明书，办事处，总代，代理，促销，特点，操作，步骤，说明书，现货，规格　　采样方法通过内置泵，采集10ml空气样品　　采样频率1-3分钟(取决于之前采集的样品)　　响应时间低浓度大约8秒，高浓度大约60秒　　体积/重量150×80×34mm/270g含电池 英国PPM公司PPM-HTV便携式泵吸甲醛检测分析仪，精度：0.01ppm，说明书，办事处，总代，代理，促销，特点，操作，步骤，说明书，现货，甲醛传感器　　传感器：PPM公司自行研发电化学原理　　检测范围：基本量程：0.00～10ppm﹝0～12.3mg/m3﹞ 另选量程：0.00～80ppm﹝0～98.3mg/m3﹞ 　　辨析度：0.01ppm　　精度：2%﹝根据于12台甲醛分析仪的4-5次重复测量，而统计出来的结果﹞　　准确度：10%﹝依据美国NIOSH所规定，使用可接受的测量方法，于相对湿度介乎于25-70%的环境中测量甲醛浓度0.3ppm。NIOSH的可接受标准是介乎真值±25%的数据结果均在95%置信区域内。而94%的PPM甲醛检测仪可达到确NIOSH的标准。英国PPM公司PPM-HTV便携式泵吸甲醛检测分析仪，精度：0.01ppm，说明书，办事处，总代，代理，促销，特点，操作，步骤，说明书，现货，温度和湿度模块　　类型：可互换的数据CMOSens 　　范围：温度：-40～+128°C相对湿度：0～100%RH　　精度：温度：±0.4°C 相对湿度：±3%RH。另可选配升级到±0.3°C，±1.8%RH。　　校正：生产商根据ISO/IEC17025进行校正，可追溯于NIST和“国家物理实验室”

公司简介： 质谱佳科技是国内专业从事分析仪器维修等技术服务、进口二手分析仪器销售和租赁的领先企业，原厂工程师团队为客户在色谱、光谱、质谱仪的维护保养、维修、仪器认证、技术升级、仪器搬迁，软硬件操作培训等多方面提供完善的技术支持和整体解决方案。 质谱佳科技在美国、欧洲、日本有着良好的合作伙伴，凭借优质的进货渠道和专业的选品团队为客户提供优质的二手仪器。主营品牌有：Thermo（赛默飞）、AB Sciex（爱博才思） 、Agilent (安捷伦)、Waters（沃特世）、Shimadzu（岛津）等，另外质谱佳科技还提供分析仪器配件、耗材的销售。 质谱佳科技总部位于长沙，通过设在上海、海口等地的分公司，形成服务全国的网络。为制药、食品、环保、三方检测、新能源等多个行业以及高校、科研院所、政府实验室等客户提供方便快捷的本地化服务。团队介绍： 公司创始人拥有Agilent、ThermoFisher等国际著名仪器公司工作经历，创办质谱佳科技之前的职位是赛默飞世尔科技（ThermoFisher）湖南售后经理，在色谱、质谱维修上拥有丰富的实战经验。公司拥有多名工程师，均由原厂资深工程师培训授课，全面掌握仪器维修技能。进口分析仪器第三方售后服务市场在国产替代的时代背景下，正加速发展，质谱佳科技也在持续招聘行业内的专业人员加入，扩大我们的团队力量。合作客户： 质谱佳科技自创建以来，凭借精湛或者专业的技术、快捷的服务、经济的价格赢得了众多客户的信赖。我们服务的客户和合作伙伴遍及全国各地，覆盖了第三方检测、制药、食品、环保、化工等行业，以及高校研究院所、政府实验室（药检、海关、质检、食检）。技术团队： 1.技术力量雄厚：公司创始人有世界顶级的分析仪器厂商的工作经验 2.自建零配件仓库：对业务所及的仪器常见的故障准备了配件，以便快速响应客户。 3.“快而灵活”的专业服务：到目前为止所有现场服务需求，我们都能够24小时内响应， 绝大多数48小时内到达现场，真正做到更快速、更周到、更专业。 4.远程支持：我们提供电话、微信、互联网远程在线支持，远程快速诊断及排除故障，大大缩短仪器停机时间，提高客户的工作效率。这些远程免费支持，对偏远地区及对仪器不熟悉的初期客户来说是一个福音。 5.完善的服务体系：我们的工程师训练有素，每一次服务都能做到规范化，可跟踪，符合各行业的法规要求。联系方式：Tel：19376980501产品展示：

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat, set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septumfor syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 piecesmulti N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vesselsfor EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)