甲烷总烃在线分析仪

规格：双填充柱材质：不锈钢配适机器型号：需客户提供相关信息柱两端中心距离：需客户提供相关信息进样端与检测端高度差：需客户提供相关信息特殊工艺制造，专用于除甲烷以外的烃类的检测分析

产品描述：可用于收集一氧化碳 （CO），二氧化硫（SO2），硫化氢（H2S），苯，氡和硫醇，碳氢化合物及氯化溶剂气体。适合短期储存低浓度（ppm、ppb级）腐蚀性气体和化学活性气体（做预饱和处理 ）。光敏化合物和卤代挥发性有机物（VOC）及非甲烷总烃的收集。Tedlar® PVF采样袋适用于采用美国EPA分析方法，包括溶出实验(TCLP), TO-3(VOCs), TO-12 (NMOC), TO-14A (VOCs), TO-15 (VOCs), ASTM D-5504及其他各种大气气体采集方法。储存温度：0℃~40℃玉衡云测是实验室设备耗材采购一站式服务商，为实验室提供专业的设备耗材集采服务。欢迎咨询：杨生：19925199703（微信同号）

产品描述：可用于收集一氧化碳 （CO），二氧化硫（SO2），硫化氢（H2S），苯，氡和硫醇，碳氢化合物及氯化溶剂气体。适合短期储存低浓度（ppm、ppb级）腐蚀性气体和化学活性气体（做预饱和处理 ）。光敏化合物和卤代挥发性有机物（VOC）及非甲烷总烃的收集。Tedlar® PVF采样袋适用于采用美国EPA分析方法，包括溶出实验(TCLP), TO-3(VOCs), TO-12 (NMOC), TO-14A (VOCs), TO-15 (VOCs), ASTM D-5504及其他各种大气气体采集方法。储存温度：0℃~40℃玉衡云测是实验室设备耗材采购一站式服务商，为实验室提供专业的设备耗材集采服务。欢迎咨询：杨生：19925199703（微信同号）

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：FITTING, FID AIR FRIT订货号：106184-00

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：Fan 4" 24v 1ea,Sample Pump 55i 1ea,Power supply 24V 1ea,Pogo Detector Assembly 1ea,Solenoid Valve Assembly - 3-Way 1ea,Solenoid Valve Assembly 1ea,Exhaust Frit Bulkhead Fitting 1ea,Pressure Controller 0-50 PSI 1ea,Rotor Replacement for 8-Port Valve 1ea订货号：115895-00

Shimadzu 总有机碳分析仪(TOC5000)注射器 体积 描述 注射器货号 替换推杆货号 250µ L 1/4-28 UNF末端 006680 031832 2.5mL 1/4-28 UNF 末端 008680 031854

奥利龙 余氯/总氯/PH分析仪产品参数：余氯总氯测量测量范围：0.01-10ppm重现性: ±3%准确度: ±5%分辨率: 0.01 ppm量间隔：2-10 分钟试试剂指示低于20%，警告试剂缺少水样要求最大压力0.5 bar，pH 4 -10，流速30-40 L/h 流量开关水样压力1 barpH 测量0-10温度测量0-50℃输出8 个 RS485，可选4-20 mA 工作温度1℃ - 45℃电源100-240 V，50-60 Hz尺寸67×33×14 cm（宽× 高× 深）/ 45 kg

ASTM D5580汽油中汽油中苯，甲苯和总芳烃分析套件 分析套件符合ASTM D5580 (SH/T 0693)标准方法，配备适当的色谱柱，用于分析汽油中的苯，甲苯，乙苯、二甲苯及C9 以上芳烃含量的色谱分析。本分析套件除了标准样品和ASTM D4815的标准样品不同之外，套件的其余部分相同，所以本套件按照ASTM D4815的方法调试后，同样可以完成ASTM D4815方法（汽油中汽油中苯，甲苯和总芳烃分析）的色谱分析 配件：进口10通阀，色谱柱1套(预柱、平衡柱、分析柱)，调试标准样品1套，阀箱1套，连接件等。 适用于：岛津色谱仪器及其他色谱仪器，安装于仪器侧面板 货号 控制电压 D5580-24 24VDC 4通 四通 6通 六通 10通 十通 自动进样阀 切换阀 样品进样阀 进样装置 进样器 气相色谱 液体进样阀 气体进样阀 定量环 MGS-4 MGS-5 VICI 7725i VALCO 手动进样阀 国标 标准 标样 石油

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：OPTION, MULTIPORT, LOW RANGE订货号：106026-02

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：55i, PROCESSOR BOARD订货号：110570-32

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：ASSY, AC PUMP订货号：104340-00

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：ASSY, PC BOARD, INPUT BD订货号：106511-00

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：O-RING SET REPLACEMENT订货号：14978

波利梅特龙 polymetronORP在线分析仪,poPolymetron 8351ORP氧化还原探头,操作原理,操作规格，说明书：销售热线：15300030867，张经理，欢迎您的来电咨询！ 在氧化还原电极和参比电极组成的测量链的氧化还原系统中，将要测量的电势称为氧化还原电势。它取决于氧化还原系统和转换的电子数量这两部分的活动度比率，在许多情况中溶液的 pH值也会影响电势。Peter的方程式定义了氧化还原电势氧化还原系统的稳定性和可逆性极大地影响被测的氧化还原电势的再现性。 波利梅特龙 polymetronORP在线分析仪,poPolymetron 8351ORP氧化还原探头,操作原理,技术参数 显示范围： - 1500 mV ~ 1500 mV 显示分辨率： 1 mV 测量精度： ± 1.5 mV 重 复 性： ±1 mV 响应时间： 10 秒内 95% 最大温度： 110℃（230?F） 自 检 查： 参比 50 K? 最大压力： 10 bar（145psi）在80℃ 电极体材料： PPS（聚苯硫醚） 电 缆： 10 米PPS 探头体（硫化聚丙烯） 9135 pH和氧化还原变送器，很独特的配置可以满足您的不同需要 机械强度且易于安装：聚酯涂层金属外壳，NEMA 4 ( IP65 ) ，通用型安装支架，适用于墙装，盘装和管道安装 清晰的图像背光显示： - 多种语言显示：英语，法语，德语，意大利语，西班牙语，荷兰语 - 可显示数种单位：pH，mV - 可同时显示测量和相关的温度 - 可显示继电器极限和模拟输出 对校准、编程和维护采用独立的通路(分别带有进入密码) 全部电流隔离： - 传感器与变送器之间 - 微处理器和电源之间，其它电路板和模拟输出之间 2个"智能" 模拟输出：0/4 ~ 20 mA - 线性，双线性或对数模式 - 可模拟环路信号以备检测之用 - 可编程平均值用于快的变化过程 - 4 ~ 20 mA输出功能用于校准，报警和维护之用 用于质量管理的数据检索： - 最后校准的日期和测量值 - 自诊断数据 - 符合规格证书 可选功能： 继电器板 (订货号：p/n. 09125=A=4000 ) - 继电器1：低或高设定点 - 继电器2：低或高设定点 - 继电器3：低或高设定点或系统报警 - 继电器4：低或高设定点或时间输出 继电器输出：250 VAC, 3 A max., 100 VDC, 0,5 A max. RS485主板：串口连接电流隔离 (订货号：p/n. 09125=A=1100 ) 详细的测试证书：(订货号：p/n. 09125=T=0000 )

波利梅特龙Polymetron9135在线pH/ORP分析仪,特点 （销售热线：13718811058，欢迎您的来电咨询，张经理）● 通用性变送器（2个高阻抗输入）：可用于复合电极、pH电极、参比电极、锑电极和氧化还原电极 ● 测量自诊断： 检查pH电极和参比电极的阻抗（专利技术） ● 可用几个通讯输出：2个模拟输出，4个继电器，RS485串口 ● 完整的变送器：脉冲触点或频率输出模式，双向比例功能 ● 校准方法的多种选择： — 自动确认缓冲液的值 — 手动设置过程校准的pH值，以及电极的偏移量和斜率特性波利梅特龙Polymetron9135在线pH/ORP分析仪,波利梅特龙Polymetron9135在线pH/ORP分析仪,参数：技术规格外壳部分符合标准： EN 50081-1 & 50082-2（EMC）欧洲标准： EN 61010-1（低电压）防护标准： NEMA 4X，IP65外壳材料： 铝和聚酯涂层金属外壳，不锈钢螺丝电缆密封： 2*PG13和2*PG11电气连接： 2.5平方毫米端子带螺丝（电源和继电器可拆卸）储藏温度： -20 - +70℃环境温度： -20 - +60℃供电电源： 100 - 240VAC，50/60Hz低 电 压： 13-30VAC，50/60Hz；18-24VDC，功率25W分析技术参数pH ： 量程：0-14pH、分辨率：0.01pH/1mV、重复性：±0.02pH/1mVORP： 量程：±1500mV、分辨率：1mV、重复性：±1mV温度：-20 - +200℃、分辨率：0.1℃、重复性：±0.2℃阻抗设置范围玻璃 ： 5M - 1GΩ参比 ： 1K - 1MΩ模拟输出： 2路0/4-20mA，量程范围可自由编程，1路用做pH或ORP和1路用做温度，2路用做pH或ORP，最大负载900ΩPolymetron9135在线pH/ORP分析仪订货号：序号名称订货号19135PH分析仪9135=A=00002超纯水PH系统08362=A=001039135CPU主板09125=A=100149135测量板09135=A=150059135电源板（标准型）09125=A=200068362PH电极08362=A=200078361PH电极08361=C=00008PH电极3米电缆359016，101109PH电极10米电缆359016，1012010PH电极20米电缆359016，1012211PT100温度探头08362=A=100112PT100的3米电缆08362=A=300113PT100的10米电缆08362=A=300214PT100的20米电缆08362=A=300315PMMA流通池08362=C=4000168350.4PH电极带温度探头08350=C=0004178350.5PH电极带温度探头08350=C=0005188351氧化还原电极08351=C=000019PH4缓冲溶液（500ml/瓶）363130,0050020PH6.88缓冲溶液（500ml/瓶）363131,0050021PH9.22缓冲溶液（500ml/瓶）363132,00500

Shimadzu 岛津总有机碳分析仪(TOC5000)用注射器订货信息：体积描述注射器货号替换推杆货号250μL1/4-28 UNF 末端0066800318322.5mL1/4-28 UNF 末端008680031854

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：ASSY, CABLE SOLENOID 3/WAY订货号：105213-00

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：ANALYTICAL COLUMN ASSY订货号：104209-00

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：Pump Repair Kit 1ea,Fan Filter 1ea,Fuse, 250 VAC 6.25 Amp SlowBlow 2ea,Aluminum Gasket (For P/N 12190) 1ea,Filter Inlet Element 0.5 micron 1ea,Ignitor/Cable Assembly 1ea,Flame Senor Assembly 1ea,O Ring, FID Flame Sensor 1ea,FID Air Frit 1ea,O-Ring Kit for订货号：115899-00

Parts for Model 55i Direct Methane & Non-Methane Hydrocarbon Analyzer产品描述：SCR, PAN HD, PH w/EXT WSHR, SS订货号：103955-00

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat, set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septumfor syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 piecesmulti N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vesselsfor EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)

北京龙天韬略科技有限公司专业提供德国耶拿TOC分析仪/总有机碳分析仪耗材配件，产品货号如下：analytikjenaConsumablesmulti N/C serieseffective from 01.01.2010 Priority Order number DescriptionCONSUMABLES TOC(all types of instruments)A 402-810.047 Special catalyst multi N/C, one filling, 40 grecommended for multi N/C 3000/3100A 402-810.048 Special catalyst platinum, one refillmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-810.050 Halogen absorber filling (copper- and brass wool)B 402-810.058 Special catalyst multi N/C, 200 grecommended for multi N/C 3000/3100B 402-810.059 Special catalyst platinum, sufficient for 5 refillsmulti N/C 2100: recommended for multi N/C 2000/2100/2100 S multi N/C 2100 S: recommended for multi N/C 2000/2100/2100 SA 402-825.044 Quartz wool, 1 packetA 402-825.150 U-tube, o.d. = 11 mm, without filling for halogenabsorber(without connections) A 402-881.006 Quartz glass cullet, coarse grains, packet of 80 gA 402-881.228 Disposable retention filter (water trap) A 402-881.229 TC prefilter (aerosol trap)402-881.245 Set of TC prefilter and water trapA 402-885.017 High-temperature mat,set of 3 piecesB 402-885.019 Halogen absorber, complete with U-tubemulti N/C 2100 and multi N/C 2100 S multi N/C 2100 WEARING MATERIALB 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.138 Dosing syringe for phosphoric acid, 5 ml 402-815.819 O-ring 15.5 mm x 2.5 mm Viton IC-vessel N/C 2100 S (Stopper)A 402-823.056 Needle 0.63 mm x 0.35 mm for all types of syringes set of 3 piecesA 402-825.041 Fork-type clamp KS 13/2 with clamping screwA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKA 402-881.238 Septa for pneumatic heads, 10 mm o.d., set of 10 piecesmulti N/C 2100: only for N/C 2100 SA 402-884.005 Pump hose for peristaltic pump, wasteA 402-885.010 Combustion tubeB 402-886.303 Syringe 100 µ l with vent and removable needle 0.63 mm x0.35 mm (only for APG 60)B 402-886.304 Syringe 250 µ l with vent and removable needle 1 mm x 0.7 mm (only for APG 60)A 402-886.305 Syringe 500 µ l with vent and removable needle 1 mm x 0.7A 402-885.011 Pump hose for H3PO4 pump mm (only for APG 60)&emsp A 402-886.306 Needle 1 mm x 0.7 mm for all types of syringes, 3 piecesmulti N/C 2100: only for multi N/C 2100 SA 402-886.310 Septum for syringe (autosampler) 9.5 mm o.d. 1 pieceB 402-886.311 Syringe graduated 500 µ l with removable needle for manual injectionA 402-886.314 Septa pre-cut for septum-head, 11 mm, 3 piecesA 402-886.317 Condensing loop multi N/C 2000/2100/2100 SB 402-886.318 Sample vials, 8 ml50 mm x 18 mm, 125 pieces multi N/C 2100: for APG 60-sampler multi N/C 2100 S: for APG 60-samplerA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC ModulB 402-889.091 Lids for sample vials, 2 ml, set of 500 piecesB 402-889.092 Sample vials, 2 ml, set of 100 pieces(for sample rack with 112 positions)402-890.100 IC condensing vessel multi N/C 2100A 402-890.110 tubing kit for multi N/C 2100 SA 402-890.111 tubing kit for multi N/C 2100B 402-890.113 needle with luer connector for H3PO4-syringe 402-890.150 IC condensing vessel multi N/C 2100 SWEARING MATERIAL Double Furnace Solids Module402-889.674 Quartz boat, 40 mm x 9 mm, set of 10 piecesA 402-890.103 Furnace sealing plugA 402-890.104 Solid combustion tubeA 402-890.105 HookA 402-890.106 Guidance tube 402-890.107 Gasket for oxygen lockA 402-890.108 Gas transfer tubing, adapter with ball jointA 402-890.109 O2 tubingmulti N/C 3100 multi N/C 3100 WEARING MATERIALB 402-000.005 Sample vials, 80 mm x 33 mm, 70 pieces multi N/C 3100: for dilution rack APG 64B 402-000.008 Stirring magnets, 15 mm x 6 mm, 10 piecesA 402-520.135 Fork-type clamp for oxygen supplyA 402-520.137 Glass screw joint (gray)A 402-815.058 Lab-type screw joint D 3.2 - GL 14, complete (red)A 402-815.102 O-rings for combustion tube, set of 3 piecesB 402-815.204 Septum silicon/PTFE, 24 mm, for screw cap EPA, set of100 piecesB 402-815.205 Screw cap for 40 ml EPA screw thread vial, set of 100 piecesB 402-820.075 Bottle Insert402-825.041 Fork-type clamp KS 13/2 with clamping screwB 402-825.099 Sample vials for dilution rack, 100 mm x 16 mm, 10 piecesB 402-825.119 Sample vessels for EPA Sampler with piercing function, set of 100 pieces40 ml EPA screw thread vialA 402-881.026 Finger-Tight-Set 1/8" for tube set, PEEKA 402-881.027 Finger-Tight-Set 1/16" for tube set, PEEKB 402-883.005 Sample aspirationmulti N/C 3100: also purge tubeA 402-884.005 Pump hose for peristaltic pump, wasteA 402-884.019 Injection tube B 402-884.021 Waste hose with screw joint (2 m) B 402-884.023 Lid for Bottle Insert 402-885.002 Condensation coilA 402-885.010 Combustion tubeA 402-885.011 Pump hose for H3PO4 pumpA 402-885.016 Sample aspiration tube with screw jointmulti N/C 3100: also purge tubeB 402-886.319 Sample vials for APG 64-sampler, 78 mm x 28 mm, 100 piecesA 402-889.050 Septum 12.5 mm set of 5 piecesmulti N/C 2100: for manual TIC - Port multi N/C 3100: for POC Modul402-890.163 Piercing sample aspiration tube for EPA sampler, titanium402-890.164 Piercing sample purge tube for EPA sampler, titanium402-890.193 Tubing kit for multi N/C 3100 402-890.200 Condensation vesselHT 1300HT 1300 WEARING MATERIAL402-815.830 Gasket for dust trap for HT furnace (34 mm x 4 mm)A 402-825.044 Quartz wool, 1 packetA 402-881.013 U-tube, o.d. = 21 mm for halogen absorberA 402-881.203 Glass tube, straight, without connectorsA 402-881.213 Headline-Disposable-In-Line-Filter, box of 10 piecesB 402-886.001 Ceran field for HT furnaceB 402-886.003 Connecting hose "Analyt" for HT furnace, 4 mm x 6 mm, 1 m longB 402-886.004 Connecting hose "pump" for HT furnace, 4 mm x 6 mm, 1 m longA 402-886.005 Connecting hose "oxygen supply" for HT furnace, 4 mm x6 mm, 2 m long B 402-886.006 Feeding tool for HT furnace A 402-886.014 Ceramic combustion tube B 402-886.114 Halogen absorber filling for straight tube A 402-886.116 Drying agentA 402-886.118 Porcelain boat (white) 1,000 piecesA 402-886.312 Halogen absorber filling for U-tube, o.d. = 21 mm(conditioned)402-886.322 Halogen absorber filling (conditioned)for U-tube, o.d. = 21 mm, set of 5 piecesWarranty claims and claims related to the fulfillment of manufacture' s technical specification can only be accepted by using original Analytik Jena components, spares and consumables.Specifications and order numbers are subject to changes due to further technical development.Prices are quoted exclusive of value added tax.Purchase is subject to the General Terms and Conditions of Analytik Jena AG.Disposable retention filter (water trap)