爆炸压力波测试装置

爆炸物检测仪，炸药探测器等设备测试标样，适用于SEED-PM系列

该测试装置用于检测糖果等休闲食品的硬度(hardness)和粘性(stickiness)。固定夹由弹簧螺栓、压盘和基盘组成，压盘中孔为测试点，在测试过程中糖果由两盘夹紧，防止发生滑动，确保实验的精确性。

爆炸物柱 Acclaim Explosives• 用于爆炸物分析(EPA 方法 8330)的解决方案• Acclaim E1 和 E2 色谱柱均对 EPA 方法 8330 的全部 14 种目标化合物实现基线分离• E1 和 E2 色谱柱具有互补选择性• 等度洗脱条件简易• 色谱柱坚固耐用，批次间可重现性良好Acclaim Explosives E1 和 E2 色谱柱专门设计用于通过 HPLC 解析“EPASW-846方法 8330：硝酸酯和硝胺”中列出的全部 14 种爆炸物。这些色谱柱采用的新式、独特化学键合相提供优异分离度，并具有互补选择性。Acclaim Explosives E1 推荐用于在初次分析中直接替代 ODS 色谱柱。AcclaimExplosives E2 可用作初次分析色谱柱或确认色谱柱。Acclaim Explosives E2 色谱柱独特的选择性和多功能性提供较广的应用范围，包括对美国 EPA 方法 8330(ISO22478) 中规定之外的爆炸物的分析。

产品介绍难以着火并具有阻止或延缓火焰蔓延能力的电线电缆通常指能通过GB/T18380.3(等同于IEC60332-3)测试的电线电缆；泰思泰克电线耐火及喷淋测试仪依据标准：BS6387而设计的，本设备用于测试电线电缆在过热、过流等非正常状态下，其绝缘层的阻燃性能。它是用来测试电缆中电流标准水平的测试装置，也可测试电缆的耐火、防水状况。符合标准? BS 6387 - 电缆在着火条件下线圈完整性测试- 附录D.3在着火状态下能保证电路工作的电缆的性能要求规范特点? 带丙烷燃烧器喷灯，燃烧器开孔为36×5mm，燃烧试验温度为650±4°? 标准燃烧器前端宽度为15mm， 小孔直径为1.32mm, 孔中心距离为3.2mm，燃烧孔3排交错排列? 装有晒水器，洒水均匀? 采用直径不大于￠2的热电偶测温。? 装有校准瓶，可随时检查和控制洒水量? 试验时试品应在额定电压和规定电流下工作，并附带指示灯反映试验状态。? 喷水器的压强范围是 250Kpa~350Kpa? 喷水量为0.25?/s/㎡~0.30?/s/㎡? 无需供水系统，箱体底部自带有水槽，可保持水循环? 仪器上有指示图以免喷水不当导致火焰熄灭? 含保护电源装置的盖子，保护其不短路? 燃烧器可将火源温度加热至 650+50°? 电压供应装置有3A或者2A保险丝；　? 有两种操作模式：控制面板人工控制或者计算机软件自动控制。这是客制化设计，用户可自行选择，如果定制IEC 60331-11,12 and BS 6387，用户可使用Slidas系统，费用会相应降低测试箱体及水槽采用304不锈钢板，防止锈蚀； 喷淋头供水压力为12~14kg/cm，满足喷淋需求； 热源为不锈钢带型丙烷燃烧器喷灯，配有Venturi混合器； 燃烧器燃烧面：400×10mm，孔中心距：3.2mm； 质量流量控制器（MFC）精确控制丙烷和空气流量； 电磁阀自动控制气源； 试验时试品应在额定电压和规定电流下工作，并附带指示灯反映试验状态。规格机型TTech-GBT19216C尺寸1,480(W) x 1,200(D) x 1,250(H)mm控制台尺寸600(W)×750(D)×1,200(H)mm电源AC 220V 3-phase, 50/60Hz, 20A 重量150 kg说明书提供排气最小 15?/min工具 吸尘器，电脑，压缩气体，丙烷气

该装置用于评估密封包装质量、强度和粘胶强度的剥离测试专用探头。 此通用装置可依据需求调整施力方向，测试容器分别以0度，45度和90度不同角度支撑。利用一个可调节的塑料皮带固定不同尺寸的容器或多样形状在质构分析仪底座位置，以夹具夹住封盖边缘往上施力测试剥离强度。 结合软件中的宏指令(Macro)，快速而准确的测试结果可作为每批次的包装材料和胶粘质量的品控，另一方面也可提供产品研发的方案。

技术参数： 采用技术：离子迁移谱技术 样品采集方式：固体颗粒物擦拭取样、液体擦拭取样、吸气取样 可检测爆炸物种类：梯恩梯、黑索今、太安、硝化甘油、硝铵类炸药、黑火药、特屈儿、奥克托今、C4炸药等、并能随时添加新样本 可检测毒品种类：可卡因、海洛因、吗啡、大麻、冰毒、摇头丸、氯胺酮（K粉）、五氯酚、杜冷丁、摇脚丸等、并能随时添加新样本 灵敏度：ng ～pg级 分析时间：2 ～8秒 预热时间：20分钟左右 供电方式：110/220VAC，50/60HZ 电池参数：22.4V锂离子充电电池，可持续工作四小时以上 报警形式：声音和可视报警，可显示发现物质种类 显示：3.5"彩色液晶触摸屏，中文(英文）界面 校准方式：内部自动校准 外形尺寸（长× 宽× 高）410× 140× 140 (mm) (16.2"× 5.2"× 5.2 ")

Rtx?-TNT/Rtx?-TNT2 熔融石英毛细柱(专利Crossbond?技术键合,)? 美国EPA 方法 8095 分析爆炸物的专用柱? 低流失—ECD 分析的理想工具? 二十分钟内完成分析? Rtx?-TNT2 确认柱在同一条件下可进行八种洗提次序的转换? 经济型三柱套装? 热稳定温度范围310°C Rtx?-TNT 和Rtx?-TNT2 是专为使用GC/ECD 分析含硝基芳香烃而设计，例如EPA8095 方法中的16 种组分分析。与目前其他的被推荐的色谱柱相比，它具有更好的分离度和较高的热稳定性。在同一GC 柱箱温度条件下操作Rtx?-TNT 基础柱和Rtx?-TNT2 确认柱。订货信息：12998Rtx-TNT1 Cap. Column6m, 0.53mm ID, 1.5um Sold as 3-pk only12999Rtx-TNT2 Cap. Column6m, 0.53mm ID, 1.5um Sold as 3-pk only

该装置使用球形探头可以测试10个个别的粘性数据，可得到单一样品的平均代表性测试值，适用于粘性指针系统(Adhesive Indexing System).

Rtx-TNT/Rtx-TNT2爆炸物的专用柱(Crossbond® 技术键合,)? 美国EPA 方法 8095 分析爆炸物的专用柱? 低流失—ECD 分析的理想工具? 二十分钟内完成分析 ? Rtx® -TNT2 确认柱在同一条件下可进行八种洗提次序的转换? 经济型三柱套装? 热稳定温度范围310°CRtx® -TNT 和Rtx® -TNT2 是专为使用GC/ECD 分析含硝基芳香烃而设计，例如EPA8095 方法中的16 种组分分析。与目前其他的被推荐的色谱柱相比，它具有更好的分离度和较高的热稳定性。在同一GC 柱箱温度条件下操作Rtx® -TNT 基础柱和Rtx® -TNT2 确认柱。订货信息：Rtx-TNTIDdf(um)温度范围6 米/3-pk0.53mm1.5-20to300/310℃12998 Rtx-TNT2IDdf(um)温度范围6 米/3-pk0.53mm1.5-20to300/310℃12999

该装置包括支撑夹和水平固定板，底座上安装摩擦滑轨，连接力臂，防止样品滑动。 位于滑轨中央的2KG砝码提供压力。在往复循环过程中测定两个方向的滑动摩擦。 典型的应用包括医疗、薄膜、刮胡膏和润肤剂等。

防静电装置 | 预防静电的产生当移液易燃液体时，如果机器和容器没有充分接地，会产生静电积累， 这可能导致失火甚至爆炸 。Bürkle防静电装置可确保简单有效地接地。防静电装置包括三种不同颜色的带钳子的铜线，均包裹轻质塑料外壳。防静电装置起批量产品货号55602-1000

The Film Support Rig allows the measurement of the resilience of fine films. Prior to performing the test, the sample is placed over a hole in a raised perspex platform. A top plate prevents the sample from slipping during testing. The test is then carried out as the arm of the texture analyser brings a 5mm stainless steel ball probe down into the aperture. The maximum force to rupture the film is recorded and is referred to as the burst strength of the strip. The resilience and relaxation properties of the film can also be measured. Resilience can be assessed by depressing the film surface to a chosen distance before retracting the ball probe. The property is calculated using a ratio of the work of compression and work of withdrawal. Similarly, relaxation can be measured with the addition of a hold period within the test to allow the product's recovery to be evaluated. Both these properties broaden the application of the Film Support Rig. Burst strength, resilience and relaxation are important factors in determining the mechanical properties of the product, allowing manufacturers to optimize product structure and formulation.

This fixture accommodates a replaceable 0.9mm thickness blade supported on a 115mm wide frame. The development of the fixture came about due to the popularity of the standard craft knife blade and the necessity then to use a thin craft blade for the cutting of deeper and wider samples.

The SMS Chen-Hoseney Dough Stickiness Rig is an improved version of the widely used and acclaimed original development by Prof. Carl Hoseney and Dr. Weizhi Chen at Kansas State University. The SMS version offers all the advantages of the original but with added durability, ease of use and ease of cleaning. The accuracy of the stickiness result is ensured by using a lapped finish cylinder probe, which has a uniform adherence surface, to make the measurement. Examples of research to date include the investigation of dough stickiness due to overmixing, addition of excess water, overactivity of proteolytic enzymes, difference in wheat varieties and composition.

This fixture comprises an upper and lower attachment with cavity dimensions defined by the customer's sample. The lower fixture is secured in the Holed plate of the Heavy Duty Platform and the upper fixture is connected directly to the loadcell. It is used to measure the adhesion performance of a tablet coating to a tablet. Samples are prepared by removing the coating around the edge of the tablet so that the upper and lower coatings are not connected. Double-sided foam tape is attached to both upper and lower fixtures, and the tablet is pushed securely into the lower cavity. The force to remove the coating from the tablet is measured.

别名：固体气体吸收器GAS PIPETTES for solid adsoro ng hemple 一、概况及用途： 该仪器用硼硅玻璃经、灯工焊接毛细管等制成， 使用时须装置在自制的木架上。它适用于固体吸收剂或盛放填．作吸收气体,如氧气厂作氧气、氮气的纯度试验。二、造型及原理：该仪器是由一个园筒形吸收球与一个园形球焊接而成，在吸收球的下端有一开口，便于放入固体吸收剂或填料，然后用塞塞住，其上端接一支毛细管 ， 是作连接气体量管用。

This rig measures the force obtained by the penetration of a multiple sample of chips. (known in some countries as French fries). Up to 10 chips can be tested at any one time and the rig ensures that each chip is completely penetrated by a 2mm diameter probe. The probe head has a fast release adapter to enable the probe to be rapidly cleaned and relocated in the same position. A perspex plate is used to hold the samples in position on the sample base.

The cheese extensibility rig consists of a microwaveable vessel and double-sided fork probe. The vessel and fork assembly is filled with a known weight of cheese and microwaved until the cheese is molten. A sample retaining insert is added to the vessel and the vessel/fork assembly slides into the fixture base, which is securely fastened to the Texture Analyser. The fork is connected to the load cell via a rapid locating adapter. The Texture Analyser pulls the fork through the molten cheese allowing the extensibility and resistance to extension to be measured. Cheese strength and extensibility are important textural attributes for many foods, most notably pizza.

This rig is used to measure the firmness and stickiness of cooked pasta. Strands of pasta are held on the texture analyser using a support block which accommodates a rectangular section exposing the pasta. A rectangular compression platen is connected to the loadcell and is used to determine the firmness of the pasta during the compression stroke and the stickiness upon probe withdrawal.

This tensile rig is ideally suited to perform break strength and elasticity measurements on both noodle and spaghetti samples. The sample is located through slots in the parallel friction rollers and then wound round two or three times to reduce any slippage and also to anchor the sample ends. The rollers ensure that the sample is not split or cut during the test and that the break occurs along the extended part of the sample.

压力传感器 压力报警装置 半自动切换 汇流排河北气路工程完工

Syringes are used in hospitals, surgeries and homes around the world on a daily basis, and for a multitude of purposes. Successful administration, as well as comfortable receipt of the material under the skin, rely on the effective tracking of the syringe piston within its outer tube. By testing the ease with which an injectable solution is expressed, manufacturers are able to optimise usability and patient comfort, while guaranteeing quality control and product safety. Prior to testing, the syringe is held securely in place by a locking insert, which is easily adjusted up to a diameter of 40mm and accommodates a wide range of syringe shapes and sizes. A flat probe, connected to the arm of the TA.XTPlus, exerts pressure on the syringe piston, measuring its resistance to compression. Using Exponent software, a mean force is produced in graph form to provide an average measure of the ease with which the syringe is depressed and fluids are discharged. The universal design of the Syringe Testing Rig also allows manufacturers to determine the force required to remove the plunger from the syringe, thus emulating the ease with which the syringe piston is withdrawn.

适用范围：非金属材料哑铃试样（薄片/ 金属薄片）可选-A或B型接头：A 轴接头 外径20mm长度30mm（配 锁紧螺母） 插销孔径10mm 插销 孔到轴端面14.5mm B 孔接头 内孔20mm深30mm 插销孔径10mm，插销孔中心到接头 端面距离14.5mm。单选钳口：平面0-9mm 可夹持试样宽度=30mm

This rig measures the compression and flexure characteristics of uncooked spaghetti which is of interest when investigating possible inherent weaknesses due to sprout damage of the durum wheat or incorrect drying procedures. The test sample is located between upper and lower supports in centrally located holes. The upper support is directly connected to the loadcell and the lower support to the base of the texture analyser. Test samples of 100mm are prepared and the average force and distance to break is measured. Attention is paid to fluctuating force before final break which would indicate weaknesses. These measurements give a good indication of the suitability of the product for packaging and transportation.

水质污染指数（SDI）测试专用膜 污染指数(SDI)测试是确认预处理过程有效性的主要方法，判断进水的结垢倾向。此款产品采用纯混合纤维素酯制成，专为SDI测试方法设计与优化。 产品特点纯MCE材质制成，不含其他支撑材料极其均匀的孔结构一致的产品质量生产和测试参照ASTM D 4189-07标准技术参数膜材纯MCE孔径0.45μm尺寸47mm颜色白色表面平整相关产品在线SDI测试装置套件 产品编号：ASDI1-PP和ASDI1-AL离线SDI测试装置套件 产品编号：ASDISYS-PP和ASDISYS-AL

实验室耦合搅拌微型高压反应合成釜系气—液、液—液、液—固或气—液—固三相化工物料进行化学反应的搅拌反应装置，可使各种化工物料在较高的压力、真空、温度下充分搅拌，以强化传质和传热过程。具有静密封、无泄漏、无裸露旋转部件，操作无需加力，釜体、加热器可完全分离，极大的方便了小型高压反应器的拆卸工作，提高工作效率。环境特点：提供反应釜内部无磁力环境搅拌反应，解决国内底部磁力搅拌含磁问题。搅拌方式：顶入式软驱动磁耦机械搅拌，正反双向搅拌，无裸露旋转部件，高速稳定，杜绝了低沸点气体蒸汽或易燃气体意外泄漏与电机电路发生爆炸危险，可做磁性材料试验。密封技术：双A通用技术，D型省力技术，解决了传统反应釜密封泄漏问题。报警控制：超温自动切断加热电源，给反应釜操作增加了一层保障。防护设计：防爆阀，实验前沿的哨兵。搅拌电机：无刷大功率马达，强劲有力，高速稳定。定时设计：定时控制和查询，无人职守，节约了试验人员的宝贵时间。进气体阀：气体进气针型阀，质量可靠，采用不锈钢一字手柄，解决了黑色塑料圆手柄不耐腐蚀、易老化的弊端。取样阀：便于反应过程中随时取样并分析反应进程，采用不锈钢一字手柄，解决了黑色塑料圆手柄不耐腐蚀、易老化的弊端。排气阀：方便在反应前对系统进行真空处理和置换气体使用，反应结束后作为放空阀，采用不锈钢一字手柄，解决了黑色塑料圆手柄不耐腐蚀、易老化的弊端。压力表：不锈钢316L材质，防震，耐腐蚀、经久耐用，实时监测反应压力。温度探头：采用内外双温度传感器设计，即可以知道反应釜体外围温度，也可插入小型高压反应器体内部，实时监测反应温度。控温系统：防止温度过冲，增加了试验的成功性。 加热单元：模块加热，加热快速。保温材料：炭纤维保温材料，加热快，环保省电。操作界面：全液晶屏操作，温度显示、速度显示，触键控制，防水面板处理。散热设计：智能温度感应，自动开启散热内部防护机制。釜体设计：釜体锻件材料加工，去强磁处理，杜绝了不稳定因素的来源。降噪处理：提供了安静的科研环境。减震设计：保证了整机工作的平稳和高速运转。延伸设计：可兼容常用水热合成反应釜，满足了多种条件的试验要求。外观设计：为您的要求设计合理结构，外观和尺寸可随您心动！技术参数微型高压反应釜（顶入式磁耦机械搅拌）型号MHK5000容 积5000ml工作界面液晶显示触键控制最高工作温度250℃加热方式模块加热加热功率3.0KW（以实物为准）搅拌速度50-1200rpm搅拌方式稀土永磁耦合驱动器搅拌功率90W最高工作压力标配10Mpa结构材质标配316L不锈钢PTFE内衬有升降功能静音电动升降额外功能替代性可替代水热合成釜

该装置通过注册，创新的设计以提供洗发精和润发精制造商评价头发的柔顺性(combability)，从而证实使用后发质得到改善。该装置的机械功能可持续重复的执行梳理动作，符合使用前后的比较实验洗发精和润滑剂需求。 头发梳理装置放在物性测试仪上，头发靠近梳子垂直放下。配合软件的指令，物性测试仪的力臂带着梳子顺着头发向下梳理，会记录移动时所需的力。到底部时，梳子往后脱离再移回到起始位置开始新一循环的测试。

Captiva 96 孔过滤装置工具包无需离心沉淀蛋白的行业标准。快速而可靠的处理过程提高了工作效率。启始工具包包含您所需要的所有备件。Captiva 独特的双层过滤介质能够完全去除沉淀的蛋白质，比离心操作更快且容易实现自动化操作，显著抑制样品堵塞。用Captiva 可以快速、可靠地处理血浆样品，并且可以永远消除纤维蛋白原堵塞。Captiva 板具有很好的样品储存能力。所有Captiva 组件都是超净的，并经过严格的测试，确保没有非特异性吸附。启始工具包包含您准备和运行所需要的一切，省心省力。更换工具包中包括了全部可更换的Captiva 配件。订货信息：Captiva 96 孔过滤装置工具包孔径（μm）过滤器材料部件号启始工具包0.2聚丙烯A5960002SK0.45聚丙烯A5960045SK包括 1 个 CaptiVac 真空夹，5 个 Captiva 过滤板，10 个 DuoSeal 96 96 孔板密封垫，5 个 1 mL Captiva 96深孔收集盘，5 个可刺透的 Captiva 收集盘密封盖可更换工具包0.2聚丙烯A5960002K0.45聚偏氟乙烯和聚丙烯A5967045K聚丙烯A5960045K包括5 个Captiva 过滤板，10 个DuoSeal 96 96 孔板密封垫，5 个1 mL Captiva 96 深孔收集盘，5 个可刺透的Captiva 收集盘密封盖

针焰测试50W火焰校准装置

针焰测试500W火焰校准装置