Ekspla PhotoSonus X 型用于光声成像的高功率DPSS可调谐激光器

报价 ¥50万 - 100万

综合评分暂无

仪器对比

品牌

Ekspla

型号

PhotoSonus X

产地

欧洲其他国家

应用领域

暂无

北京欧兰科技发展有限公司

营业执照已认证

金牌会员
第17年
一般经销商

样本下载

PhotoSonus X

High Output Power DPSS Tunable Laser for Photoacoustic Imaging

Download
datasheet

Integrated DPSS pump laser and OPO system
Up to 90 mJ in range 650 – 2600 nm
100 Hz or 50 Hz pulse repetition rate
Certification ready
Quiet operation < 60 dB

Photosonus X - High Output Power DPSS Tunable Laser for Photoacoustic Imaging

Features & Options

FEATURES

Ultra-wide signal tuning range from 650 to 1300 nm
Fully motorized wavelength tuning
Fast Wavelength Switching
Externally triggerable
High, up to 90 mJ pulse energy from OPO
100 Hz or 50 Hz pulse repetition rate
Certification ready
Quiet operation < 60 dB
Integrated DPSS pump laser and OPO into a single housing
Fiber bundle or fiber
Signal and Idler through the same output (optional)
Integrated energy meter (optional)
Electromechanical output shutter with laser self-test capability

Description

PhotoSonus X is a perfect solution for photoacoustic imaging in pre-clinical and clinical use and when fast sample scanning is required. Having high output energy of up to 90 mJ at the peak, a broad wavelength tuning range from 650 to 2600 nm, high pulse repetition rate up to 100 Hz and fast wavelength switching makes it a perfect photoacoustic imaging source for gaining high-resolution images and ensuring high data acquisition rate. Moreover, being built on a diode pumped solid-state laser platform, PhotoSonus X assures significantly quieter operation (< 60 dB) compared with flash-lamp pumped lasers, which is very beneficial for clinical use.

Diode pumped laser technology and well-engineered system design ensures high reliability and low-cost system operation. PhotoSonus X output can be coupled with almost any type of fiber bundle.

With additional options of an internal energy meter and electromechanical shutter with laser self-test capability, PhotoSonus X can be ready for certification in clinical photoacoustic applications.

Specifications

MODEL 1)	PhotoSonus X-50	PhotoSonus X-100
OPO
Wavelength range
Signal	650 – 1300 nm
Idler (optional)	1065 – 2600 nm
OPO output pulse energy 2)	>90 mJ	>50 mJ
Pulse repetition rate 3)	50 Hz	100 Hz
Scanning step
Signal	0.1 nm
Idler	1 nm
Pulse duration 4)	2 – 5 ns
Signal linewidth 5)	< 15 cm-1	< 10 cm-1
Typical signal beam diameter (1/e²) 6)	6 ± 1 mm
Control interfaces	LAN, RS232
PHYSICAL CHARACTERISTICS
Cooling	Closed loop air-water cooled 7)
Unit size (W × L × H)	551 × 400 × 162 mm
Power supply size (W × L × H)	483 × 390 × 140 mm
Umbilical length, m	0.5 m
OPERATING REQUIREMENTS
Room temperature	18 – 27 °C
Relative humidity	20 – 80 % (non-condensing)
Power requirements	100 – 240 VAC, single phase 50/60 Hz
Power consumption	< 2 kW

Due to continuous improvement, all specifications are subject to change without notice. The parameters marked typical are not specifications. They are indications of typical performance and will vary with each unit we manufacture. Unless stated otherwise all specifications are measured at 700 nm.
Measured at the free space output. See tuning curves for typical energy levels at different wavelengths.
Other fixed pulse repetiton rates are available upon request.
FWHM measured with photodiode featuring 1 ns rise time and 300 MHz bandwidth oscilloscope.
At 700 nm or higher wavelength.
Measured at the free space output at 700 nm wavelength.
Using external chiller.

Note: Laser must be connected to the mains electricity all the time. If there will be no mains electricity for longer that 1 hour then laser (system) needs warm up for a few hours before switching on.